Jump to content

Watch in the pool ?


Recommended Posts

So ladies and gentleman, i recently bought myself a vostok amphibia 420059 which is still on it's way hence there is not picture. I'm going on vacation soon and wanted to bring the watch with me. I've never worn an automatic in the pool/sea, except a casio quartz movement. I know the casio can take a beating and it's only a 30 euro's but i'm asking you professionals if it is a good idea to take my watch in the pool and if i need to do something after swimming (rinsing the watch with water) ? I loved to hear so i can enjoy my watch for a long time! 

Link to comment
Share on other sites

Scuba dude!

These watches are meant for being thrown around.  Enjoy it.

Before getting wet, always check that the crown is screwed down.  After being in the sea or a pool, run it under the tap to wash away any sand and chemicals.  It's also a good idea to turn the bezel a few times to release anything stuck under there.  Then towel dry it and leave it somewhere warm to evaporate any excess water.

Enjoy your holiday.

Link to comment
Share on other sites

Even the best quality diver watches are only secure if they have been regularly serviced with new seals fitted. Another mistake which is common wearing them in the shower or bath the hot water just creeps in. I know because my son did exactly this with his Breitling, luckily he knew someone who could fix it 😀😀.

Link to comment
Share on other sites

2 hours ago, Len33 said:

NO WATCH is "waterproof,"

not entirely true one of the early LED watches known as the SYNCHRONAR 2100 RIEHL SOLAR was hermetically sealed. there's a link below that talks about the watch it unfortunately doesn't have the best picture of the module. the second link seems the missing it's taxed but does show pictures of the module. So basically the entire module is sealed up it's probably the closest I would know to anything that is waterproof. Unfortunately because that is sealed the rechargeable batteries go bad with time and your watch is now worthless.

https://anachronar.wordpress.com/2018/06/04/its-back―a-review-of-the-synchronar-2100-mk-iv-and-a-half/

http://www.crazywatches.pl/synchronar-2100-riehl-solar-led-1974

 

On 6/11/2021 at 8:20 AM, Corstjens1 said:

casio can take a beating

yes but it's not a Timex. You want to look at the early Timex advertisements like this one you will note he ask he uses the word waterproof.

 

Link to comment
Share on other sites

On 6/15/2021 at 1:29 PM, Len33 said:

 

Divers' excepted, I personally cannot understand why anybody would want to take a watch into water.

 

I get it but i do want so sip on a nice margharita when i'm in the pool and not constantly have to take my watch of. I'm also very anxious with leaving stuff at the beach while i'm in the water so that's why I don't want to leave my watch laying around. 

Link to comment
Share on other sites

Ok. I hope your holiday goes well and that you enjoy your margarita on the beach.

However, I think that getting "Boris" to allow you to go away represents far more of a threat to your holiday than water entering your watch does!

Good luck.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello everybody, sorry for the late reply. Thank you all so much for your help and your tips. I got lucky and found a replacement wheel bridge for cheap which actually ended up being in decent condition. I decided not to do anything about the mainspring barrel pivot since I didn't have the right tools and the barrel didn't have much endshake anyhow. I am happy to report that the watch now runs great, I have regulated it to about +-10/s day which is fine by my standards. The timegrapher result looks decent as well, although beat error is around 0.6ms which could be better I suppose. Amplitude reaches over 230 quite consistently which I'm happy with also. My lighter fluid has also been replaced by balance spring cleaning solution and now the springs don't stick to themselves anymore - who would have thought. I'm super happy with this watch, it might not be worth a whole lot but it's awesome that I could restore it and it makes me wear it with pride. To me it's a genuinely good lucking watch, it'll be my daily driver for a while. Thanks again to everybody for their input! I couldn't have done the repair without your help.   Here are some images for those interested, the bracelet isn't original but I don't really mind:    
    • Balance-hairspring system is oscillator with big Q-factor. When all in the movement is OK, the rate (frequency) is verry close to the own resonant frequency of the balance-hairspring. But in some cases, the movement (with foult) will force the resonator to work on pritty different frequency, sometimes faster, and sometimes slower. When this happens, the amplitude is always weak. So, the first thing to ask is what is the amplitude. If it is more than 180 and the hairspring doesn't touch itself and anything else, then for sure it is 'short'. If the amplitude is weak, then the first thing to do is to understand why and rectify the problem. At this time no point to check timekeeping. But, if one doubts that the hairspring is not correct, then He needs to calcullate the rate of the movement, then to 'vibrate' the balance-hairspring out of the movement and to measure the free oscillations frequency (period) with timer in order to ensure that they comply with the rate. If we have pictures, then it will be easier to tell something about that wheel.
    • So much work has gone into this! Thanks again @Jon. I will go back and check my adjustments from last weekend. A few questions for you, if you don't mind. In the reset position, I can understand the problem if the gap between the hammer and the minute counter heart is too big (slide 77) but what is bad about both hammers being in contact with the cams (slide 76)? I read somewhere that Landeron recommended grease on the runner cam, but the minute counter heart should be dry. Is that so, and why? How many tads in a ligne?
    • Could you glue two pieces together for rigidity and separate after forming? 
×
×
  • Create New...