Jump to content

Asking for help with Timex Automatic:

KarlvonKoln
 Share

Recommended Posts

KarlvonKoln Distinguished Member

KarlvonKoln

Posted
Posted

I have on my bench a Timex Automatic (would it be a Viscount, circa 1979?) marked 37869 10979, 38 mm dia. with day & date. Symptoms that the owner/dealer wants me to correct are 1) the stem does not seem able to find that first detent where the date & day can be set, and 2) crown is unbelievably worn down and he wants a new stem-&-crown if I can get one.

I think I might need a new setting lever too. So far, the impression I get is of a degree of wear.  The stem *seems* to slide in and out almost too easily.  And I can't get it to stay in that sweet spot where the day or date rings turn.  I will be stripping it down further in a bit, but I wanted to hear if this might be a common problem.  I'm also hoping @JerseyMofinds this.

20210528_235931.jpg

20210529_202949.jpg

Link to comment
Share on other sites
JerseyMo Distinguished Member

JerseyMo

Posted
Posted
20 hours ago, KarlvonKoln said:

OMG!  So that's how it's done!  I tried this and it works!  So there's nothing wrong with this watch after all; it's just a pain in the behind.  Man, glad you'd only need to update the date once in a while.  Thanks a million @HectorLooi!

yep, remember these are budget watches and features such as "quick set" were not available.  That crown is way over worn and if you give me the dial code printed the below the 6 hour I'll look to see if I have a replacement.

Link to comment
Share on other sites
KarlvonKoln Distinguished Member

KarlvonKoln

Posted
  • Author
Posted (edited)
3 hours ago, JerseyMo said:

yep, remember these are budget watches and features such as "quick set" were not available.  That crown is way over worn and if you give me the dial code printed the below the 6 hour I'll look to see if I have a replacement.

Mo, I'd be much obliged.  I've had terrible luck knowing where to scare up exactly the right crown.  The code reads: 37869 10979.  If you have one, my dealer friend will be very happy. He asked me to try to get it as usable as possible. And if it comes with a stem in it, I'd be more than grateful.  I couldn't get the crown off, even with heat.  And I didn't want to twist it too far and cause damage, so I'd begun searching for a crown/stem combination, which was proving harder still.  For all that they're a very different kind of watch to work on, they do seem like rugged little beasts.  Kinda like the old dollar watches from earlier, you could bang 'em around a bit on the job and still know what time your shift would end.


Addendum: I have to say, it's a clever little set of ratchet pawls they use to wind it by the oscillating weight, where swinging it one way causes one pawl to catch while the other ratchets, and vice versa with the pawl on the other side.  A cheap and simple solution that accomplishes the same thing as a system of gears.  I don't often get to work on a Timex, so I was surprised by that little rocking contraption. 

Edited by KarlvonKoln
Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchrepairIRE
      Crown Snapped Off - Armani Renato Watch

      By watchrepairIRE · Posted

      Thanks again for all the help. I found a number on the movement (715) after much searching. I guess it's the below movement so I will order than and see how I get on. https://www.ronda.ch/en/productfinder/caliber/715
    • watchweasol
      Casio AQ-321G Battery

      By watchweasol · Posted

      Hi. Thing to do is measure the battery space.  Diameter.  X depth ..    I have seen it listed as  sr626sw.  377 measure to check then check the dimensions of the 377.    
    • DouglasSkinner
      Hillabold's Pallet Setter

      By DouglasSkinner · Posted

      Hello!  Does anybody have this tool?  This is mine.  If you have one, does it look complete?  How do you use it.  (I have the instruction sheet but it's hard to read!)  thanks!
    • arron
      Ball PW balance staff and hands

      By arron · Posted

      @JohnR725 that's very helpful.  I appreciate the time you took to give those instructions and post the pictures.  below is a picture of my staff, which looks identical to the ones you posted.  The approx measurements I got are: .772 on the left part of the staff; .715 on the right side of the hub; the hub is 1.107; and the overall length (minus the broken pivot) is 5.248; which seem to line up with the measurements you posted.  I didn't think to measure the pivot, which I'll do if there's enough of one left on the staff.  Thanks again.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Thank you to both of you!  I've been somewhat derailed by this quandary for a couple of days now. I am guessing that the point of the wider tweezers is to support the whole spring at the same time in an effort to prevent it going under tension... I have already discovered the Zen of a clutter free space, and trying to keep my work well away from the edge, however the most terrifying of the flights wasn't so short, I had my work in the middle of the table and nothing else around.  That particular launch was towards me.  I distinctly recall feeling the spring hit my left hand as it escaped.  I only found it by dumb luck, on the floor, between the legs of my chair.  I need to order a pack of replacements just in case.  I think I recall a thread discussing where to find them, and the differences between the clones and the authentic ETA ones, pointing out that they're not interchangeable (the clones being longer IIRC).  Now I just have to find that thread again.  What I haven't mastered is the zen of the search function here.  I'm sure I"ll get that down eventually. So this is similar to, but different from one of the posts I had found in my original searches (or maybe I'm just hallucinating, I can't find the post I thought I remember).  The bits about the corner filled in a gap in what I'd read before.  At least I have a more clear picture in my head about what needs to happen now.  Yes, I've learned about how touchy these springs are.  What I'm not sure I have a good grasp on is the understanding of what causes the spring to flex, other than to say "the slightest little touch"  I think I'm going to try a small bit of Rodico to position the spring next time.
×
×
  • Create New...