Jump to content

New Video. Repairing A Vintage Gold Watch Case

Mark
 Share

Recommended Posts

Ishima Super WRT Addict

Ishima

Posted
Posted

I have a slightly outdated book 'Practical Jewellery Repair' by James Hickling, his illustrations and explanations on soldering were slightly different to this, it seemed more difficult. 

Is this gold brazing paste a fairly recent invention? Or am I as ignorant to jewellery repair as I think I am.

Link to comment
Share on other sites
DMLarsen New Member

DMLarsen

Posted
Posted

Nice job Mark!!  I've been wanting to try this on a solid gold ladies watch that has a hairline crack in the case.  I just don't have the proper torch fittintgs yet.  I have a large torch leftover from my autobody days, but my tips are a bit too big for this delicate type of work.

 

Again Nice Job Mark!

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • DouglasSkinner
      Hillabold's Pallet Setter

      By DouglasSkinner · Posted

      Hello!  Does anybody have this tool?  This is mine.  If you have one, does it look complete?  How do you use it.  (I have the instruction sheet but it's hard to read!)  thanks!
    • arron
      Ball PW balance staff and hands

      By arron · Posted

      @JohnR725 that's very helpful.  I appreciate the time you took to give those instructions and post the pictures.  below is a picture of my staff, which looks identical to the ones you posted.  The approx measurements I got are: .772 on the left part of the staff; .715 on the right side of the hub; the hub is 1.107; and the overall length (minus the broken pivot) is 5.248; which seem to line up with the measurements you posted.  I didn't think to measure the pivot, which I'll do if there's enough of one left on the staff.  Thanks again.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Thank you to both of you!  I've been somewhat derailed by this quandary for a couple of days now. I am guessing that the point of the wider tweezers is to support the whole spring at the same time in an effort to prevent it going under tension... I have already discovered the Zen of a clutter free space, and trying to keep my work well away from the edge, however the most terrifying of the flights wasn't so short, I had my work in the middle of the table and nothing else around.  That particular launch was towards me.  I distinctly recall feeling the spring hit my left hand as it escaped.  I only found it by dumb luck, on the floor, between the legs of my chair.  I need to order a pack of replacements just in case.  I think I recall a thread discussing where to find them, and the differences between the clones and the authentic ETA ones, pointing out that they're not interchangeable (the clones being longer IIRC).  Now I just have to find that thread again.  What I haven't mastered is the zen of the search function here.  I'm sure I"ll get that down eventually. So this is similar to, but different from one of the posts I had found in my original searches (or maybe I'm just hallucinating, I can't find the post I thought I remember).  The bits about the corner filled in a gap in what I'd read before.  At least I have a more clear picture in my head about what needs to happen now.  Yes, I've learned about how touchy these springs are.  What I'm not sure I have a good grasp on is the understanding of what causes the spring to flex, other than to say "the slightest little touch"  I think I'm going to try a small bit of Rodico to position the spring next time.
    • HectorLooi
      Casio AQ-321G Battery

      By HectorLooi · Posted

      I think it's stamped on the inside cover. 309 I think.
    • Waggy
      Casio AQ-321G Battery

      By Waggy · Posted

      Hi all, needing a little help. I have an old Casio AQ-321G, but have no idea what battery it takes. I've looked around online, but cannot see anything... I see a 309 stamped on the case back, could this be it....? Can you please help, below are some pictures:
×
×
  • Create New...