Jump to content

Recommended Posts

Hello to all,

My name is Ash (from NZ). Im a watch enthusiast and trying to learn more about Horology.

I have been picking odd watch repair jobs here and there and self-learning.

Firstly, thanks a lot to Mark Lovick for uploading fantastic videos on youtube that are so simple to follow. Keep up the great work :)

Question - is there a way to diagnose quartz watch circuit using those test probes (that have an LED inbuilt) or perhaps using a multi-meter? For some watch movements such as Myota 2035, it makes sense to replace the whole movement. In other cases, it make sense to repair it (if possible).

Is there a way to narrow down the faults in quartz watch? For instance, if a watch is gaining/loosing time, it could be the quartz crystal out of freq etc. how can it be scanned appropriately?

Im not sure if its even possible or not. Hopefully I could get some help here.

Thanks a lot in advance

Ash

Link to comment
Share on other sites

A friend of mine who's an amateur, but very competent, repairer, has a machine on which he places the watch - minus battery. When he presses a button, the magnetic mechanism inside the machine kicks in and turns the watch movement and hands at high speed. If the hands and movement don't whizz round, he considers the quartz movement to be probably beyond repair - broken circuit board, faulty coil, etc. If the movement does run on the machine, then it may well be repairable.

 

Apologies if you know this already - I speak as an observer - and apologies for not knowing what the machine's called!

 

Oh - and a warm welcome to the forum!

Edited by WillFly
  • Like 1
Link to comment
Share on other sites

Hello Ash,

                 Welcome to the forum,  which seems to be growing very rapidly, by the way.  I'm afraid I do not know the answer to your question, but I think a good place to start would be to find out the name of the quartz tester Will mentions above.  There are members at all skill levels on the forum and no doubt someone will have more advice for you.

  • Like 1
Link to comment
Share on other sites

I thought that if it's any other thing than the coil it's u/s. But isn't there something about a coil being separate from the board that changes the games a little. Like the boy's have said the name of that device would be handy and knowledge from the man would be good. There are many levels of skill on the forum so good luck with it and Wecome to the forum btw. ;)

Link to comment
Share on other sites

Yes you will need a multimeter and access to the data-sheet for the movement will be a help.

 

Israel's tool looks really good, but I have not got one. 

 

Other meter's made by Witschi are extremely expensive but are industry standard, they rarely come up on eBay but you could get a bargain from time to time.

Link to comment
Share on other sites

A friend of mine who's an amateur, but very competent, repairer, has a machine on which he places the watch - minus battery. When he presses a button, the magnetic mechanism inside the machine kicks in and turns the watch movement and hands at high speed. If the hands and movement don't whizz round, he considers the quartz movement to be probably beyond repair - broken circuit board, faulty coil, etc. If the movement does run on the machine, then it may well be repairable.

 

Apologies if you know this already - I speak as an observer - and apologies for not knowing what the machine's called!

 

Oh - and a warm welcome to the forum!

hi WillFly,

 

thanks a lot for your comment. that machine is called 'demagnetizer'. if the movement runs freely on magnetizer, that generally means gear train is fine. it also means the fault lies either in coil or circuit. i do have one of those already. its a cheap chinese one but does the trick :)

 

I was more keen on learning how to fix the circuit, if possible. I have succesfully fixed few coils. they are not too bad. Le arsi has got a good video on it

 

 

Cheers for your help :)

 

Ash

Link to comment
Share on other sites

thanks a lot to Autowind, Craig, SeikoWatch & Mark Lovick for their comments.

 

i have been thinking of building something similar to what LeArsi shows on youtube. looks like a good nifty project :)

 

Most of all, really appreciate the wearm welcome i have received on this forum so far. Glad to be a part of it.

 

i have got one more queestion re Watch crystal glass. I will make a seperate thread for it.

 

Regards

 

Ash NZ

Link to comment
Share on other sites

that machine is called 'demagnetizer'. if the movement runs freely on magnetizer, that generally means gear train is fine. it also means the fault lies either in coil or circuit. i do have one of those already. its a cheap chinese one but does the trick :)

 

Not sure I recommend a de-magnetiser. I know it pushes the wheels around but my fear is it would potentially affect the stepping motor. I have no evidence of this - it's just that I can be a cautious bugger :)

 

The Etic Polytest and Omnitest both have that function plus they generate a signal to indicate if power is going through the circuit.

 

 

They are great machines, and come in very handy - I have had them for years.

 

Sadly they are no longer being manufactured but I do understand there are some alternatives out there.

 

post-1-0-08582600-1392936734_thumb.jpg

 

I have fixed a few coils in the past but circuits are not my thing, if I feel one is damaged I would rather replace it if I can ;)

Link to comment
Share on other sites

  • 5 months later...

Hi Ash welcome to the forum. I'm curious too about your question so please keep us posted of any progress...and if you build a tester I might be interested! Quartz is not my line of expertise ( and barely the others either, I'm a beginner).

Link to comment
Share on other sites

  • 4 months later...

Dear fellow members,

 

I currently own the pictured tester, nevertheless, I'd like to do a more in depth testing on individual circuits in the watch, like component resistance/impedance, continuity, etc. This one is supposed to do some but is not a full meter.

 

post-253-0-24486900-1417460566.jpg

 

 

Do you have a suggestion of what would be a good amp/ohmmeter and/or full tester for in depth work on digital watches? Thank you in advance,

 

Bob

  • Like 1
Link to comment
Share on other sites

Thank you clockboy, I do too, but regretfully this movement I will be tackling is US$100! I'm talking about the ETA 251.272 and the next in line in my workbench is not much better, ETA 251.471, same price! If all is well, it will be very rewarding to have them going again without a transplant!

  • Like 1
Link to comment
Share on other sites

I recently serviced an Omega DeVille quartz watch...

 

Held my nose while I opened the case, but lo and behold the movement was actually a lovely lovely thing. Thirteen jewels and the bare minimum of plastic.... i'll dig out a pic...

 

Actually Dave the Watch Guy has a teardown of exactly the same watch:

 

http://watchguy.co.uk/service-omega-ladies-deville-calibre-1471-quartz/

Edited by mwilkes
Link to comment
Share on other sites

When replacing a battery in a Quartz Movement I check the consumption and rate.  This is a good indication of the health of the movement.

 

Consumptions:

 

Basic 2 Hand >900nA

Basic 3 Hand >1.5uA

3 Hand with Complication >2.0uA

Chronograph >2.8uA

 

Rate should be very low ... like +0.15 sec/day

 

If I get high consumption readings, the movement needs a strip and clean.

 

If I get no readings, I check the coil for damage or corrosion ... if it's good, then I isolate and check the Quartz is oscillating, and then isolate and check the IC.  Either of these two are the issue, then you need to replace the circuit ... because most manufactures won't sell you a crystal, or coil these days, which stinks!!

 

The machine I use is the Witschi Q1.

Link to comment
Share on other sites

Thank you Lawson,

 

Very clear instructions. Do you have a suggestion for a good volt-amp meter appropriate for this? I don't think I'll get into a witschi right now although I'm already drooling at the sight of it. :)

 

Cheers,

 

Bob

Link to comment
Share on other sites

When replacing a battery in a Quartz Movement I check the consumption and rate. This is a good indication of the health of the movement.

Consumptions:

Basic 2 Hand >900nA

Basic 3 Hand >1.5uA

3 Hand with Complication >2.0uA

Chronograph >2.8uA

Rate should be very low ... like +0.15 sec/day

If I get high consumption readings, the movement needs a strip and clean.

If I get no readings, I check the coil for damage or corrosion ... if it's good, then I isolate and check the Quartz is oscillating, and then isolate and check the IC. Either of these two are the issue, then you need to replace the circuit ... because most manufactures won't sell you a crystal, or coil these days, which stinks!!

The machine I use is the Witschi Q1.

I believe you made mistake,there are maximum values for every movement provided in the technical document of the manufacturer of the movement, as it is written in your post now it seems that there are minimum values, whuch is not correct.

Besides the values of power consupmtion there are two values whiich should be checked also:

Lowest working limit(voltage on which movement stops working)

Rate i dont need to explain this

br

emso

p.s sent from my sh**y phone, so sorry for typing mistakes

Link to comment
Share on other sites

emso, on 06 Dec 2014 - 06:17 AM, said:

I believe you made mistake,there are maximum values for every movement provided in the technical document of the manufacturer of the movement, as it is written in your post now it seems that there are minimum values, whuch is not correct.

 

ROFL! :D  Sorry I always get those stupid symbols back-the-front ... They are max values peeps, and I'm an idiot :p

 

emso, on 06 Dec 2014 - 06:17 AM, said:

Besides the values of power consupmtion there are two values whiich should be checked also:

Lowest working limit(voltage on which movement stops working)

 

Oh yes, I forgot to mention the lowest working limit. 

To explain, this is when you connect probes to the battery terminals, sent a set voltage to the watch, and note if it's still running.  Starting at 1.5V and dropping down from there (you can set these voltages on the tester).  A good movement should still be ticking at 1.3V, and at this point, or below, should be going into it's "Low Battery Warning" mode of ticking off 2 seconds at a time.  Then lower the voltage more until the watch stops, and note down that voltage.

Link to comment
Share on other sites

Thank you Lawson,

 

Very clear instructions. Do you have a suggestion for a good volt-amp meter appropriate for this? I don't think I'll get into a witschi right now although I'm already drooling at the sight of it. :)

 

Cheers,

 

Bob

 

Sorry mate, I don't know of one.  I work on Quartz all day at work, so I only do mechanicals at home.  And the cost of these testers is crazy expensive!

 

I have been told, and seen, that cheaper one have trouble testing some of the Japanese Movements, so if you are serious about buying a tester make sure you do your homework that it covers all the bases.

Link to comment
Share on other sites

  • 11 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...