Jump to content

How to tell mechanical from electric at sales?


Recommended Posts

So, I know this is a total newb question, but I am a total newb, so here goes...

There you are at an estate sale and you want to pick up some inexpensive mechanical

watches to learn on, how do you know for sure it's mechanical, without taking the

back off?  Obviously, if it says "Quartz" on the dial it's electric, but will it always  say that?

Any other give-aways?

Thanks for the time!

 

Link to comment
Share on other sites

Hi Tom,

If it's a runner and has a seconds hand check that. If the seconds hands jumps from second to second it's a quartz watch. If it is sweeping from second to second with barely noticible interuptions it's mechanical. In the unlikely event that it's electrical and has yet a sweep second: buy it. It's most likely a pre-quartz tuning fork watch and a collectors item.

Cheers and all the best from Hamburg

Alex

  • Like 1
Link to comment
Share on other sites

Electric (battery driven spring oscillator) and quartz watches were a big thing when introduced, so they usually advertise this on the dial.

Also, while technically quartz are battery powered and thus electric, if you see "electric" or "electronic" on the dial it's very likely one of a number of battery powered, balance wheel designs. For this reason quartz watches are usually not referred to as "electric"

https://en.wikipedia.org/wiki/Electric_watch

Link to comment
Share on other sites

My quick-glance go-to is to look at the crown. Aside from Seiko 5s from a fews years ago and back (which are obvious in their own right), all mechanical movements I'm aware of (even automatics) can be hand wound. In order to be able to be wound, the crown has to be large and knurled enough to do so. Quartz watch crowns are intended to be used a few times a year, and only for setting, so they're almost universally smaller and not very knurled. Mechanical watch crowns [i]can[/i] be very small and smooth if they're super worn, but they'd likely also be badly brassed to go with the wear, and be obvious that way. There can absolutely be overwrought quartz watches with big crowns to look like they're mechanical, but typically they'll be pretty obviously chitzy and give themselves away that way.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
×
×
  • Create New...