Jump to content

Venus 175 persistent magnetism problem


Recommended Posts

My beautiful 1946 Brietling, which I use as my every day timepiece, was given a full service about 4 years ago and returned (after more than one year!) looking new! Ever since it has had to be returned regularly +/- 9 months to be demagnetised.

About 9 months ago I contacted general manager of Bristling service in UK and begged them to tell me what I can do to protect it and fix the problem when it recurred. With so much of modern living dependent on equipment using magnetism we agreed that it would be very difficult to protect the watch from daily exposure. Instead they suggested I should purchase the same demagnetiser that they use and do it myself. This I have been doing, regularly about monthly, but it's timing has gone haywire again today - it has now gained 10 mins in 7 hours!

The device I am using is "Antimag 2", from Helmut Klein GmbH, Pforzheim, Germany. Thank you very much.

Miles Robinson

I should be most grateful for any advice as to how I can restore the watch to perform as it should.

Link to comment
Share on other sites

17 minutes ago, MilRob said:

it's timing has gone haywire again today - it has now gained 10 mins in 7 hours!

I suggested that you have the watch checked and regulated. It's absolutely normal for mechanical watches to occasionally require that. 

Link to comment
Share on other sites

A hairspring coil, specially if ever been manipulted,  might foul itself or stick in dynamic state( on wrist) but run Ok in static position, so bench testing your watch can be a useful observation. In case you see no difference, post a close up video of the coil when running, it just might reveal an issue. 

This amount of magentisation every month is uncommon unless your watch regularely gets exposed to an abnormally strong field. 

Regs 

Joe

 

 

 

Link to comment
Share on other sites

This is a bit odd, or I feel misleading, because you have been getting the same problem with magnetism at fairly regular intervals, although the effects are not cumulative. By that I mean repeated exposure to a low-level field repeatedly over time doesn't build up to a higher level of magnetism. A watch gets magnetised by a one-off exposure to a field of sufficient strength. I can only assume that the regularity of your 9-month intervals has been a coincidence. Your preventative once-a-month treatment isn't going to help against that, but it shouldn't hurt either.

Have a think about what you did today that was unusual, where you went, and where that exposure could have occured.

As for restoring the watch to perform as it should, I'm afraid there isn't much you can do other than avoid magnetic fields as much as possible.

Link to comment
Share on other sites

@MilRobWhat do you do for a living?  Electrical engineer?  MRI scanner operator?  Compass manufacturer?  Live on a ley line?

All joking aside it may be worth carrying around a small compass to see if anything in your environment is causing strong magnetic fields.

Link to comment
Share on other sites

Thank you all for your comments on the persistent magnetisation of my 1946 watch. Most seem to think I have an odd lifestyle to have exposed it to such 'intense' fields. I have done an extensive search with my handheld compass without success. The only culprit I can think of is the case to my mobile phone which has a magnetic closure. I have tried to demagnetise this without success, and have looked for an alternative cover similarly without success.

As said Breitling supplied me with the demagnetiser they said they used (cost £265) and I contacted the German manufacturer for their advice. They replied that Breitling had supplied me with the wrong device! Am currently in contact with their General Manager to supply me with the correct device. Yuk!

At the moment I am considering selling it but reluctant as it was a wedding anniversary present.

Any other advice gratefully received.

Link to comment
Share on other sites

6 hours ago, MilRob said:

As said Breitling supplied me with the demagnetiser they said they used (cost £265) and I contacted the German manufacturer for their advice. They replied that Breitling had supplied me with the wrong device! 

These are hugely inflated prices, you can buy a demagnetizer (bluebox type) for €12 which works just fine. 

Link to comment
Share on other sites

7 hours ago, MilRob said:

Thank you all for your comments on the persistent magnetisation of my 1946 watch. Most seem to think I have an odd lifestyle to have exposed it to such 'intense' fields. I have done an extensive search with my handheld compass without success. The only culprit I can think of is the case to my mobile phone which has a magnetic closure. I have tried to demagnetise this without success, and have looked for an alternative cover similarly without success.

As said Breitling supplied me with the demagnetiser they said they used (cost £265) and I contacted the German manufacturer for their advice. They replied that Breitling had supplied me with the wrong device! Am currently in contact with their General Manager to supply me with the correct device. Yuk!

At the moment I am considering selling it but reluctant as it was a wedding anniversary present.

Any other advice gratefully received.

I doubt your demagnetiser will demagnetise the permanent magnet in your mobile phone case, get rid of the case rather than your phone. It seems the likely culprit. 

Link to comment
Share on other sites

I don't understand the "wrong device" comment, to be honest, except that it is a far better and more expensive piece of equipment than you really need. A very nice gift though, and no doubt it will de-magnetise your watch whenever required. If the watch is still running wildly fast after using the Antimag, then the watch has another problem. What was the latest result?

It is Important to understand though, that the best de-magnetiser in the world offers no protection against future exposure to magnetism, like washing your hands doesn't stop them getting dirty again.

You don't necessarily have an odd lifestyle, you just live in a different world to the people who designed and built your beautiful Breitling. Magnetic fields are everywhere these days, and your watch is from a bygone era. The cause could well be the magnetic clasp on your case. It makes sense to eliminate it.

Link to comment
Share on other sites

12 hours ago, Plato said:

I doubt your demagnetiser will demagnetise the permanent magnet in your mobile phone case

Of course. One really has to handle a Neodymium magnet to appreciate how incredibly powerful these are. 

Link to comment
Share on other sites

These permanent magnets will not demag.  I experimented some time ago with  a rotor from a quartz watch, and found it impossible to demag, even using a very strong field.  Put them near a mechanical watch and you can actually see the balance hairsping change shape in some instances !!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • As an experiment i was thinking of not hardening it to see how it fairs. Now that i have a complete template i could knock up another in half the time if this loses its elasticity. I might play about with a few pieces today to test their bending and spring properties. This was cs 100 the supplier quoted in annealed state, it was nice to work with files so I'm taking it thats its state. What you are looking seems like it would need annealing to work it. This is why i went for this stuff that cuts out that process, it was so easy to work.
    • Showing state of hairspring on receipt, backplate & 'dished' wheel. 
    • I would harden and temper (to a light blue). It's so easy to do and only takes a couple of minutes. A search on ebay UK for "spring steel strip cs" finds plenty available in small quantites and thicknesses from 0.1mm up.  But the question is ( @nickelsilver) which "CS" number is best for watch parts ?  Also, from one of the ads : "CARBON SPRING STEEL. SIZE IS METRIC 15.00mm X 0.10mm X 304 MM  CS100 FINISH BRIGHT . HARDENED AND TEMPERD TO 480-530VPN" I've no idea about 480-530VPN. Does that mean it needs annealing before working?       Have you seen this video, he shows how to determine where the indents go ?  
    • Here is the insert ring for rectangular or elliptical movements: Note that the length is the side with the stem cut out on the spreadsheet (in the picture below this is 15.15: Here is the fake pdf file, again you need to convert to .zip after download to access the FreeCAD and 3mf files. Rectangular insert disc.pdf    
    • as you took the mainspring out what did it look like? It's amazing how much amplitude you can get if the mainspring actually has the proper shape. last week I was doing a 12 size Hamilton and was very much surprised with the beautiful back curvature the mainspring had. Then the watch had a really nice amplitude the group would be so proud it was 350 until I dropped the lift angle down to 38 that drop the amplitude quite a bit below 300. then with the beautiful back curve it still had really nice amplitude the next day. I really wish all my mainspring's look like this as the watch had beautiful amplitude the next day. So many of the aftermarket pocketwatch Springs I see now do not have anything resembling a back curve may be a slight curve and that's about all. They still work but they just don't work as nice as a properly made spring. then Omega as all sorts of nifty technical documentation unfortunately every single corner is watermarked with where it came from who downloaded it etc. very paranoid company. On the other hand I will snip out images like from the document on recycling a mainspring barrel. for instance here's the section on what your mainspring should look like. water damaged a lot of times means rust was there rust on this watch?
×
×
  • Create New...