Jump to content

Quartz conversion of HMT manual wind watch


Recommended Posts

I love the dial of this inexpensive Indian made HMT manual wind watch.

image.thumb.png.f25ef43bd3d42df753a6b9715faca9ef.png

One day, the minute hand of the watch came lose and was rotating rather freely.

As I was trying to figure out how to remove the movement/dial from the case, I used too much lever force on one of the inside plates and it broke. On further investigation, the watch is opened from front and back.  Only then can the movement/dial be removed; from the front!

It sat in my drawer for months until one day I came across cheap SL68 quartz movement in Aliexpress.

The original hands couldn't fit the SL68 movement.  Holes were too big.  But I discovered that the hour/minute hands from a spoilt quartz Swatch watch fitted the movement very nicely.  The only that couldn't fit was the second hand.

The crown from the HMT watch could be unscrewed from the winding stem and screwed on the SL68 stem. The SL68 stem just needed to be trimmed to the correct length.  Took the opportunity to fit some tiny O'rings over the SL68 stem before setting it in so that water won't enter the watch case thru it.  It can probably just withstand light rain splashes as there are no o'rings in the back/front case.

The dial had 2 pins which blocked the movement from being positioned correctly despite snapping it off.  Hence, the dial is a little off centred.  One day, I'll get a dremel tool to slowly file off the pin remnant so that the movement can be positioned properly.

The movement is stuck onto the dial using double sided tape!

I lost the manual winding function but at least am happy to be able to continue use this watch.  Am now waiting for a watch which uses an SL68 movement to spoil so I can recycle the second hand.

 

 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
×
×
  • Create New...