Jump to content

Radium burn


Graziano

Recommended Posts

Here is a cool piece of history that I picked up. It's a ww2 military Elgin nos with the original crystal, check out the radium burn. The Watch stopped at 2.30. It works well. I will service it soon, it has a 594 movement. The original box and bag is displayed. 

Cheers Graziano 

IMG_20210423_183756.jpg

IMG_20210423_183729.jpg

IMG_20210423_183718.jpg

  • Like 5
Link to comment
Share on other sites

9 hours ago, Michael1962 said:

Where do you find these things Graziano?

Hello Micheal1962, I picked this up from a gentleman who sells antique and vintage items out of Tasmania on ebay. I have a few of these ww2 Elgin pocket watches and this one is very interesting as it has the original box and crystal with the radium burn. That shows that it has sat somewhere for years and years in the box. Not very often you come across radium burn. Have a great day Micheal 

  • Like 2
Link to comment
Share on other sites

On 4/23/2021 at 3:25 PM, Graziano said:

Not very often you come across radium burn.

my understanding is the military radium products are very very bad compared to the civilian. Usually the watchmaking point of view you'll see radium burn on the dial I've never seen it on a crystal. The other place where I see it is the old hand assortments. Hands were mounted on a piece of paper and the radium hands if you move the hand you can see where burn the paper. This even came up the other day somebody asked about it I showed him the hands the radium hands you could see the paper was burned.

unfortunately for watch repair, you will see it as I said on dials occasionally the hand assortments if you're still on the paper occasionally. The problem watch repair is things like the hand assortments there's a brand-new hand assortments from whatever it doesn't have a date on it most people wouldn't know the radium unless you knew what to look for. Unless you have a Geiger counter you don't know that that nice assortment a hands that you bought some of them are radium. So unfortunately the radium stuff is still around unless you have a Geiger counter unless it burns the paper a dial or crystal he can't look at him and tell entirely. Then you only see the burn if it stays in one place long enough to burn something.

  • Like 2
Link to comment
Share on other sites

19 minutes ago, JohnR725 said:

my understanding is the military radium products are very very bad compared to the civilian. Usually the watchmaking point of view you'll see radium burn on the dial I've never seen it on a crystal. The other place where I see it is the old hand assortments. Hands were mounted on a piece of paper and the radium hands if you move the hand you can see where burn the paper. This even came up the other day somebody asked about it I showed him the hands the radium hands you could see the paper was burned.

unfortunately for watch repair, you will see it as I said on dials occasionally the hand assortments if you're still on the paper occasionally. The problem watch repair is things like the hand assortments there's a brand-new hand assortments from whatever it doesn't have a date on it most people wouldn't know the radium unless you knew what to look for. Unless you have a Geiger counter you don't know that that nice assortment a hands that you bought some of them are radium. So unfortunately the radium stuff is still around unless you have a Geiger counter unless it burns the paper a dial or crystal he can't look at him and tell entirely. Then you only see the burn if it stays in one place long enough to burn something.

Hi there John, a big variable here is that the age of radium burns isn't necessarily a function of the age of the watch, but rather of how long the watch has been stopped. And the materials that burn. The dial has damage as well as in the enamel shine of the black dial is gone from most of the dial. I quickly put the front cover back on because there was significant amounts of lume dust around. I will remove this when I service it. The Watch ran well when wound and kept spot on time for the day then I just let it wind down, I to have not seen crystal radium burn, but I am guessing that this watch looking at the case which is like new could have sat in the dark in its box for up to 60 years maybe. I will keep that crystal with the Watch as I think it is amazing for a collector. 

Cheers Graziano 

Link to comment
Share on other sites

On 4/27/2021 at 11:42 AM, HectorLooi said:

So... how are you going to display this lovely piece of history?

A lead lined box with a thick piece of leaded glass?

Hi Hectorlooi, I haven't thought about that. Do you have any suggestions. And I should also display the crystal too don't you think? 

Link to comment
Share on other sites

I have no idea. For radiation safety, a box lined with lead foil would be advisable. But I'm not sure how thick the lead foil should be. In my xray room, the walls are lined with 1mm lead. 

Perhaps a medical equipment supplier dealing with xray equipment could advise you.

Link to comment
Share on other sites

On 4/28/2021 at 2:03 AM, HectorLooi said:

For radiation safety, a box lined with lead foil would be advisable. But I'm not sure how thick the lead foil should be.

the problem with radiation is typically you don't see it. There are examples of people seeing the effect of radiation usually the outcome on the people were very bad.

really the best way to figure this out would be to find somebody with a Geiger counter preferably a sensitive one. Find out how much lead you need to isolate yourself from the radium. Unless of course you just isolate the item from you in the house or wherever you are. Then of course there is the other problem if you put it in your landline box you going to keep opening it up to look at it you might have to get some  lead glass and that's probably going be considerably thicker than the lead itself. They might just be better to have a picture of it someplace in and put the item somewhere else away from people.

then I have some pictures for you since you like pictures. The radium burn on the card that the hands are on isn't really that spectacular. Most people probably wouldn't even notice I just happen to know what it is. We also don't know how long they've been there we can guestimate when they last made hands with radium.

that I knew we had something lurking in the shop I found it. As we can see a nice watch I should've set the hands C Elledge burning was on the dial I didn't think about that did very clearly see the crystals when burned.

radium burn crystal dial.JPG

radium burn hand one.JPG

  • Like 2
Link to comment
Share on other sites

On 4/29/2021 at 7:37 PM, JohnR725 said:

I knew we had something lurking in the shop I found it. As we can see a nice watch I should've set the hands C Elledge burning was on the dial I didn't think about that did very clearly see the crystals when burned.

Hi there John, probably a good idea for collectors and repair people of vintage watches to have a look through their collections or parts containers and remove radiation and place in a  contained storage  box before other damage is done to the young over time ,or your good watches that have been sitting next to it for years. 

image.png

Link to comment
Share on other sites

4 hours ago, Graziano said:

Hi there LittleWatchShop they have got to sit there for 100 umpteen years

100 years is a little on the long side. If I remember when I'm at work again I'll look at the watch we could probably come up with a date of when the watch was made that would give us a clue.

5 hours ago, LittleWatchShop said:

I don't see any indication of radium burn on the inside of the cover/lid.

we run into problems with the subject. For instance how strong is the radium it has a half-life of thousands the years so that's not the issue of the half-life but how strongly did they mix it up? If you looked at the hand I had that was on the paper it's barely burned at all. Versus burning the crystal in the examples but as a guess that radium is probably a much higher concentration. Radium hands in a glass vial there's not a lot to burn other than the paper around it but I'm guessing they're too far away.

  • Like 1
Link to comment
Share on other sites

Hi all ,a new study from the good folks at the University of Northampton has shown that we all forgot one essential fact: radium decays to radioactive radon GAS, which is readily inhaled and will in sufficient doses significantly increase the risk of lung cancer. Radon is the second leading cause of lung cancer in the USA after cigarette smoking; the EPA estimates that radon is responsible for about 21,000 cancer deaths annually.  but it seems that logical steps to take might include considering ventilation issues, and investing in a radon detector for the room in which you keep your collection (radon monitors are inexpensive and recommended for most homeowners anyway).

Edited by Graziano
  • Like 1
  • Thanks 1
Link to comment
Share on other sites

I had a little time just before I was leaving to look at the watch. I was going to see what the date was there's no date code on the back and the movement conveniently did not want to come out and I didn't really want to be handling it anyway.

what I found interesting was that the burning was only on the crystal? Usually in the past if I've seen a radium burn it would be on the dial itself. With a hands and stayed stationary for a long time. But in some ways another example of without the crystal you can't look at the watch itself and see if that's radium.

rb5.JPG

rb4.JPG

Link to comment
Share on other sites

47 minutes ago, JohnR725 said:

Usually in the past if I've seen a radium burn it would be on the dial itself

Did you know that at the time radium was the most valuable substance on Earth, selling for $120,000 for a single gram—$2.2 million at today's value ,just a bit of trivia.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
    • The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
×
×
  • Create New...