Jump to content

Tag Heuer crystal glass replacement guidance


Recommended Posts

I have this Tag that is getting a new crystal.  (My neighbor discovered my hobby!)  I ordered a generic 24mm by 2mm from Ofrei because this is what I measured of the broken crystal and the inner diameter of the watch.  I measured before removing the crystal and then after removing, I pieced together to confirm.

I have watched the WRT video on this topic, so I think I understand.

When the crystal arrives, I am going to use my crystal press and push!

When using the press, I will use the correct adapters so that the movement sits planar to the press.

If there is any special consideration due to it being a Tag, please let me know.

I bought two crystals because...well...it is my first time ?

Edited by LittleWatchShop
Link to comment
Share on other sites

  • LittleWatchShop changed the title to Tag Heuer crystal glass replacement guidance
14 hours ago, LittleWatchShop said:

 I ordered a generic 24mm by 2mm from Ofrei because this is what I measured of the broken crystal and the inner diameter of the watch. 

That works if the crystal is flat without bevels, but an expensive watch it may have some subtle features. And even if the original was mineral glass I'd recommend to the owner to fit a sapphire one. 

The measurement is made with the crystal removed, to inner diameter of the gasket. 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
×
×
  • Create New...