Jump to content

Issue with Bulova 23


Recommended Posts

Hello all,

was working on servicing this Bulova 23 I got at a pawn shop.  It was running before, but stopping.  I stripped it all down and cleaned it.  I was putting it back together and oiling it today and I finally got the balance back it and this is what it is doing.  I have checked the banking manually and it looks ok so I am guessing the balance is the issue?  Any help is appreciated.

https://photos.app.goo.gl/CS44qkVSn1YwgFmt8

it is like the balance banks everything correctly and then stops

Link to comment
Share on other sites

It looks like something is rubbing or scraping. The above suggestions seem likely.

For these watches, it is common for the hairspring to rub against the arms of the balance wheel or against the underside of the balance cock.

You might confirm that the wheel isn't rubbing against the pallet bridge or the center wheel.

  • Like 1
Link to comment
Share on other sites

Observe the coil from side view of the balance while running, a close up video of balance looking streight down on the bridge and side view showing the coil helps.

Coil should be flat, level with concentric circles and not foul itself.

Judging from the previous video, amplitude seems good which is a sign of hairspring free from rubbing, however you give the balance plenty of swing when you nudge it,  instead gently move the wheel see if it picks up and go at some point. (I think the balance is out of beat)

I always put just  the balance complete and bridge back( no other part)  on the mainplate for final adjustment leveling etc.  it will give you almost 330 access to the HS  around the balance wheel 

What happens if you turn a gear, third or center ? 

 

 

 

 

  • Like 2
Link to comment
Share on other sites

I'll second that it's a good practice to replace just the balance complete prior to assembly so you can get a good look at the hairspring.

After doing that, you can add the pallet fork and bridge to see how the fork and jewel interact.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Thanks so much for all the suggestions, troubleshooting alone is super frustrating.  I did inspect the teeth on the escape wheel under magnification for a full rotation and didn't see anything out of the ordinary

 

Here are some more videos of it running.  Excuse the potato quality.  I was filming from my ipad through a magnifier.  Though it seems to have decided to start running since last night.  The only thing I did different since this was to give the balance complete a lighter fluid bath

Bulova 23 issue https://imgur.com/gallery/PN5Ocr7

 

Edited by Wdschell
Link to comment
Share on other sites

Solved I think...

I decided to give everything another look and low and behold the pallet fork stones basically fell out while I was inspecting it.

I decided to check them with just a little pressure and the moved.  Best to get a new fork or can these be glued back in?

IMG_20210302_142944__01.jpg

  • Like 1
Link to comment
Share on other sites

53 minutes ago, Wdschell said:

 Best to get a new fork or can these be glued back in?

Pallets are usually shelaced since it wont harm the base metal forks are forged out of, Marks shows how to make this tool to warm the fork on and shelac the pallet jewels, I use epoxy five on cheap pieces.

 Pallets adjustment is no easy task, nevertheless if you like to give it a try, there be plenty help and advice besides Marks lessons.

I couldn't find a link to relevent threads , some one may have more luck than I and find em.

 

 

  • Like 1
Link to comment
Share on other sites

Loose pallet jewels would do it. This is an uncommon fault, so it's worth reflecting on the cleaning procedures to see if something could have dissolved or softened the shellac. You might also check the roller jewel, which is also secured with shellac.

Replacing the jewels is not too hard, but replacing them to the proper depth is another matter. It's interesting and worth trying, but you might source a replacement pallet fork for now while you read up on it.

  • Like 1
Link to comment
Share on other sites

10 minutes ago, WellAdjusted said:

Loose pallet jewels would do it. This is an uncommon fault, so it's worth reflecting on the cleaning procedures to see if something could have dissolved or softened the shellac. You might also check the roller jewel, which is also secured with shellac.

Replacing the jewels is not too hard, but replacing them to the proper depth is another matter. It's interesting and worth trying, but you might source a replacement pallet fork for now while you read up on it.

Dang I didn't think about the roller jewel dissolving too.  I used some generic jewelry cleaner on the fork.  I just lighter fluid on the balance complete.  I'll check it.  I am currently sourcing a 10bzac movement for the fork.  I think Dave's watch parts has one.  Waiting to hear back

Link to comment
Share on other sites

12 hours ago, Wdschell said:

pallet fork stones basically fell out while I was inspecting it.

It's extremely unusual that the pallet stones fallout I would definitely change your cleaning fluid. Sometimes they can be loose but usually there's visually still shellac on them

Then if you decide to put the stones back in they have to go in a specific location. The angle on each stone is slightly different so you have to put the right stone in the right slot. Then a course comes the fun of adjustment which is why we use shellac because it allows you to warm it up shellac softens the stones can be moved in and out as necessary.

Then you want to be careful when you using generic jewelry cleaners or other cleaning fluids because interesting things can happen that normally wouldn't happen if you're using proper fluids. Jewelry cleaners are not usually expecting all sorts of different metals and that can result in interesting undesirable consequences also.

7 hours ago, Wdschell said:

the impulse jewel is safe

.Roller jewel's especially on American pocket watches do tend to suffer more than the pallet stones. So in the case of a pocket watches it's always worthy to check the roller jewel to make sure it still  locked in place.

 

Link to comment
Share on other sites

Just wanted to update this thread again. 

It was indeed my fault for using the wrong cleaner to clean the pallet fork.

I got the new parts movement yesterday, installed the pallet fork and was having the same issue.  The escape wheel looked fine but since I had another I went ahead and swapped it in and voila, it is ticking away and I cant hear or see anything wrong with it now.  I inspected the old gear, but I just cant see anything wrong with it.  Even compared it to the one I swapped in. 

Looks great on the time grapher now.  Thanks for all of your help in this.  Mostly, I need to bounce ideas off of someone when troubleshooting and you guys were awesome for that.  I am sure I will be around again as I think my Seiko 6139 has a loose canon pinion ?

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Getting back to the issue which is us guys repairing or just enjoying horological exploits. The big worry now is how sound is Cousins as company going forward. The of cost if this 8 year legal battle will be astronomical. Cut backs will happen noticed already how the Cousins catalogue is half its size this year. The main supplier going out of business will hit the UK horological community in a big way.    On the Brexit issue it was about a sovereign country being able to make its own laws and trade with any country in the world. I cannot see what was wrong with this. For those who wish to re join the cost would be very high indeed.
    • Yes, it's the same (old) song and it's getting worse & worse;  
    • 🤔 leaving the EU meant that UK was no longer part of the convention and have already been turned down an independent reapplication. I'm pretty sure courts have to be held in Switzerland in this case. There will be a lot more watches stashed away in draws  tbh, folk wont be able to afford to maintain them. Cheap watches will be bought and top end watches by folk with plenty of cash that can pay for service and repair. The expensive once in a lifetime gifts and everything else inbetween will be at the forgotton when they stop working. I know i was being a numpty, get used to it 😄 Anybody that knows will boycott them, but besides repairers who will know. Nope will never buy one, i made that decision as soon as i learnt about this. 
    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
×
×
  • Create New...