Jump to content

Polishing Cases

handwound

By handwound
in Watch Repairs Help & Advice

 Share

Recommended Posts

handwound Watch Enthusiast

handwound

Posted
Posted (edited)

Hi guys,

I'm currently working on a project, a Seiko Pogue. I already finished the movement and wanted to restore the case now. So I ordered polishing pads for hand finishing and a polishing machine and polishing wheels for final finish. Also I got 3 polishing pastes. I wanted to try the polishing machine on a watch where it doesn't matter when I ruin it. It had some really light scratches on the caseback, so I wanted to try there. I started with the second paste (for pre-polishing) and it was working okay. I got a lot of really fine scratches, but better than before. So I proceeded with the third paste (for polishing) and it was only making scratches, no mirror finish. I tried different wheels but that didn't changed anything. What am I doing wrong? Too much pressure? The wrong pastes? Wrong polishing Wheels? Also I wondered that the paste was really hard, I expected it to be soft, is that normal?

Here you can see the tools I used: 

 

image.thumb.png.f028d91cd4cd100154a6d11bf333683f.png

This is the polishing paste

 

polierscheiben_uhren_uhrmacher_drahtbuerste_filz_uhren__schwabbel_polieren_filzkegel_beco_technic.thumb.jpg.648a7f1e9c37a7245e90b0550aab6811.jpg

the polishing wheels (from Beco)

 

 

xenox_tbx_mhx_uhrmacher_poliereinheit.thumb.jpg.9b45d32a68503d22d08b6467f8ca8839.jpg

and the polishing machine.

 

 

 

Edited by handwound
Link to comment
Share on other sites
Yasser Member

Yasser

Posted
Posted

Hi,

I think it’s the type of polishing wheels in my opinion.  You need very fine fibre wheel.   Check ebay.     Also check retro watch guy website as he listed in order what he uses.    

I hope it helps.

Regards,

Yasser.

  • Like 1
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

Polishing cases is a very big subject; you can do a 6 week course at WOSTEP for many thousands of bucks and still a debutante (well you'd be better than 90% out there but needs thousands in equipment).

 

Without seeing exactly what you're up against it's hard to say. One big thing, when going for a fine (scratchless) polish is cleaning - clean your case ultrasonically and use different buffs for different grits. The buffs don't forget what was there before and you can't clean it off.

 

 

  • Like 1
Link to comment
Share on other sites
handwound Watch Enthusiast

handwound

Posted
  • Author
Posted

First of all thanks for your answers.

i know that I‘m not going to be a professional polisher after reading some posts about it, just as I‘m not a watchmaker, despite being able to perform a service and some repairs. I just don’t have the proper education and above all just not the experience. 
 

I just want to improve the condition of the case a bit. I‘ve tried to work with less polishing paste and higher rpm now and the results were a lot better, but I still get some swirling. Also I can’t say what caused the scratches in the beginning, the case was clean, the wheels too. And the scratches were really obvious, not these very fine ones.

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

The polishing machine you have is a dental laboratory/jeweller's micromotor. When I polish metal with a handpiece, I prefer to start with silicone wheels.

Silicone wheels come in different diameters, shapes and grits. The coarse grits can remove deep scratches and can even round off edges if not used properly. They can give a nice brushed finish. 

Medium grits give a nice satin finish. For final polishing, I use a hard felt wheel with polishing compound. But mostly I prefer to switch to a bench polisher with a larger diameter felt wheel or muslin wheel.

  • Like 1
Link to comment
Share on other sites
handwound Watch Enthusiast

handwound

Posted
  • Author
Posted (edited)

Yes, I chose one with handpiece because I don’t have the space for a bench polisher and I thought it would give me more precision with the smaller wheels.

I will remove the deep scratches by filing the case by hand, I will use the polisher just for the final touch. Otherwise I would be scared to lose the edges. So I don’t really need to use a silicone wheel.

Edited by handwound
Link to comment
Share on other sites
WellAdjusted Member

WellAdjusted

Posted
Posted

It's a mix of equipment and technique.

For getting a finish free of microscratches on stainless steel, I use loose 4" cotton wheels and the Menzerna family of compounds. I step down from blue (if needed) to pink to yellow to white. In between each step, clean the case with a steamer or an ultrasonic cleaner. You can get true mirror polishing, with no swirls or scratches under a 10x loupe and raking light, this way.

An underappreciated side of this level of polishing is contamination. Different grits shouldn't be used on the same wheel, or course, but think also about your fingers, how the piece is cleaned and wiped down, and so on. A fine finish will be scratched if a piece is wiped or dried with something that has old compound residue on it.

 

 

  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...