Jump to content

Dial Finish and Luming.

mcoulton

By mcoulton
in Watch Repairs Help & Advice

 Share

Recommended Posts

mcoulton Watch Enthusiast

mcoulton

Posted
Posted

Hello

I have two questions.

1.) I'm restoring a brass plated dial with newly lumed numbers. Do I protect the dial by spraying on a clear or mat varnish from Humbrol Paints? I don't have an air sprayer so I would either apply the varnish via a brush or an aerosol can. What do you recommend?

2.) Does newly applied lume cure to a hardness that can be sanded down? I may have a few areas where the lume is built up and won't allow the hands to pass. Instead of removing the lumed area and reapplying it, I'm wondering if I can simply sand down the high spots?

Thanks in advance for any advice that can be given. 

Michael

Link to comment
Share on other sites
Graziano WRT Addict

Graziano

Posted
Posted (edited)
8 hours ago, mcoulton said:

 I'm wondering if I can simply sand down the high spots?

Hi there , sanding down the lume would make marks that may not be visible to the naked eye but would be clearly visible under magnification .Why not strive for perfection and redo the lume,after all this is what watchmaking is all about and practice makes perfect ,then you will learn the properties of applying lume.Not only that but you risk damaging other parts of the dial .If at first you don't succeed, then try again as the saying goes.Take your time and strive for perfection.After all your are doing a restoration .

hope this helps ,Graziano

Oh and I forgot to mention sanding the lume will remove the fine natural film on the surface leaving rough surface allowing mould and other types of defects to occur more quickly   

Edited by Graziano
  • Like 1
Link to comment
Share on other sites
Graziano WRT Addict

Graziano

Posted
Posted
1 hour ago, mcoulton said:

Hello

Thanks for the suggestions. I've never worked with lume before and so I don't know the properties of it nor what I can and can't to it. This watch and it's dial will be a rewarding learning experience. 

 

Michael

Hi there Micheal, here's a link to a video, that should help you understand luming 

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
×
×
  • Create New...