Jump to content

Tool for polishing watches

bojan1990

By bojan1990
in Watch Repairs Help & Advice

 Share

Recommended Posts

bojan1990 Watch Enthusiast

bojan1990

Posted
Posted

Hello

I would like to learn to polish watch cases and bring them back to life. Would something like Dremel 3000 do the job? I guess the number of RPM is important to be able to do the final polish properly. I prefer to do everything I can by hand and the last part to finish with a rotational tool.

Thanks.

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted

I do use a drummel tool for stainless steel watch cases as it will remove all scratches. I have some YouTube videos on this from years ago.  Use red paste and rpm around 15, which I assume is 1500rpm. Do not do this with anything but stainless steel and mask all other areas of the watch. Done this many many times.

Link to comment
Share on other sites
WellAdjusted Member

WellAdjusted

Posted
Posted

You can do righteous work with one of those tools. I prefer a bench polishing lathe (I can hold the piece with two hands and use larger buffing wheels), but I find I use a handheld tool often, too. Clamping the piece in a bench vise helps avoid slips and increase control.

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is.
    • Malocchio
      What tools does ebay have to offer this week.

      By Malocchio · Posted

      I recently bought this but not on ebay. I figured if I want something Japanese I better check Japanese auction sites since these don't seem to pop up on ebay. I paid 83 € plus shipping & taxes. I think it was pretty reasonable for a complete set in good condition.
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Did you take the friction pinion off the large driving wheel and grease it? Although, now that I think about it, that shouldn't have any effect on the free running of the train if the friction pinion isn't interacting withe minute wheel/setting wheel...
×
×
  • Create New...