Jump to content

Tension-ring crystal replacement tool. Any options?

MrRoundel

By MrRoundel
in Watch Repairs Help & Advice

 Share

Recommended Posts

MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

Greetings, gents.

I'm in the process of replacing a tension-ring crystal on a vintage 1954 Girard Perregaux wristy. I was not aware that it used such a crystal until after I popped it out in a couple of pieces. Bugger was really in there. I tried finessing it out with a standing pliers style GS press but no luck until I bore down a bit harder. I had also tried a crystal clamp but it wasn't able to squeeze the crystal down enough to press it out, even with taps of a nylon hammer head.

Unfortunately the case bezel grew a bit since I first took what I thought was a good measurement of it and ordered that size crystal. And of course the crystal I got is too small. On the next measurement I found out that the bezel grew about .2mm since the first measurement. ?? As I read up on installing tension-ring/armored crystals I discovered that you don't have a lot of tolerance for a crystal that is too large. .1mm is the maximum oversize from bezel that one should use. This, according to the Sternkreuz catalog details. It also seems that I might not be able to use my GS press, nut-cracker/plier style to install it. In addition, I read that it's quite difficult to install them using the nylon dies that come with the inexpensive case presses. Do I have any chance in fitting the right crystal with the nylon dies (Some dies do have the chamfer to fit over the edge of the crystal and reduce its diameter a touch.) or do I have to buy a "real" crystal press that's heavier duty, or at least uses threads for applying the pressure?

The case is a nice 14K case that I don't want to distort. I think I now understand how it is that some watch cases have broken lugs, etc. People probably using the wrong press and/or applying too much pressure. Any suggestions are appreciated. Many thanks. Cheers all.

 

MrR

 

Link to comment
Share on other sites
Klassiker Distinguished Member

Klassiker

Posted
Posted

There are already a few threads on here discussing this. Mark also made a video. As you say, size is important. Get the size you think you need, and one size bigger. You can rub down the o.d. if necessary. The press you have with the angular contact dies should do the job if the crystal is the right size. The claw tool is the wrong one for this job. You need to get the crystal lined up with the bezel, and the pressure from the die needs to be equal all around.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...