Jump to content

Wittnauer Compressor Diver

LittleWatchShop

By LittleWatchShop
in Your Watch Collection

 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted (edited)

My Dad gave this to me on my 14th birthday.  I had wanted it for several years.  Some years later, I had another dial made for it that was customized with my name on it.  I kept the original dial. 

Today, I finally got the courage to take it apart and restore the original dial.

Judging from the lume on the hands, I am guessing that maybe I did that myself a lifetime ago.  Part of me wants to have the dial and hands refinished to match.  The other part of me says no...leave it be.

Maybe a little surprising that I would be nervous about doing this today.  Already in the last few months, I have disassembled and reassembled several watches (one a chronometer Chronograph) without much fan fare.  But, this watch is personal...the others were from the junk box.

 

1028653413_2021-01-2210_58_28-Photos.png.2dee7e1144804891ed46b3a47f520c5f.png

Edited by LittleWatchShop
corrected chronometer to chronograph
  • Like 2
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
27 minutes ago, PastorChris said:

I know that opinions vary wildly on such things, but I'd keep it the way it is, save for servicing to keep it running well. I'd love to see the custom dial you made, even if you prefer to plus you name out.

Here it is.  They did a pretty poor job IMO.

I ordered a set of NOS hands (for a pretty penny!).  When the new hands are installed, I will post an update.

Old dial_edit.jpg

  • Like 1
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

OK, the new (NOS) hands came in today and I installed them.  Goodness what a challenge.  Hour and minute hand fit just find but the second hand hole was too small.  Argh!!  Fortunately, my dad had a very good collection of broaches in his watch bench.  I had seen them but forgot which drawer.  Double argh!! 

Well, found them and put the finest on a pin vice and carefully increased the hole size.  I would put the original hand on the broach and measure how far it extended and then compare with the new one as I reamed.  Nerve-racking for sure.  But I got it.

Here is the watch with the new hands.  Much better with matching lume.

2021-01-29 16_32_54-Photos.png

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...