Jump to content

Stem stuck as if completely wound ?? Working flawlessly until today ???

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

My Wittnauer chronograph which I have owned for the better part of my life suddenly exhibits strange behavior.

Short story:  I wound it yesterday (like everyday), it runs, today I went to wind it and the stem acted as though the watch is fully wound.  What could be wrong?

Longer story: This watch sits on my desk along with about seven other watches that I monitor daily.  Been sitting here for several months (previously it had been stored away in a jewelry box).  It has been working flawlessly until today.  I opened the back, but, alas, it is a chronograph.  I cannot see the rachet wheel or click.  I was going to release power and then rewind it but, like I say...cannot get access to this stuff.

My watchmaking renaissance is in its infancy. I have repaired several watches in the last couple of weeks and only lost a couple of components (grrr!!!).  I am many months (years) away from tackling a chronograph.  I will probably take it in for repair unless someone on this forum can share the magic bullet.

Thanks in advance!

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

The Valjoux 23 and 72 and their cousins all suffer from weak ratchet wheel teeth. A tooth can break at any time; I am thinking that on the last winding a tooth came off and is now jamming things. The click is just barely visible through a hole to the left of the chrono castle wheel viewed as in the pic if you want to try to let the power down, but it will need full disassembly to get to the ratchet wheel.

  • Like 1
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

Just a follow up on this issue.  When I engage the crown, slowly turning in the winding direction, I feel the engagement and the resistance of the click.  So, I hypothesize that the winding wheel is engaging the rachet wheel.  Could still be a broken tooth lying around blocking the rachet wheel from turning.

I have three choices: 1) take it to a professional to have it fixed, 2) practice for a year and then tackle it myself, 3) do nothing.

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
5 minutes ago, watchweasol said:

Hi what you must remember when doing any dismantling work is to photo each stage it will give you a record of what you did and where the parts all fit, memory is a fickle thing.

AMEN to that brother!!!  I have been doing that, albeit a little carelessly.  Gonna be very detail oriented going forward.  In the video posted, the watchmaker noted returning screws to their position after removing respective parts--so as not to get screws and their locations confused.  This is very clever, I think.

I ordered the part today.  Still not certain I will attack it, but at least I will have the part on hand for me, or a skilled watchmaker.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...