Jump to content

Has this ever happened to you?

saswatch88

By saswatch88
in Watch Repairs Help & Advice

 Share

Recommended Posts

saswatch88 WRT Addict

saswatch88

Posted
Posted

So check this out I had an elgin 539 a-11 hacking movement with a bad balance, i swapped the balance and realized it just did not work, (and yes i checked the hack lever, the stem was still in) I did nothing to this movement, didnt disassemble clean or do anything. I put the movement back in my organizer bin, and a couple days ago I opened it to start the service on it. However oddly enough as soon as I picked it up it started ticking away, so then I winded it up put a dial and hands on it and boom! This thing is still running! its been almost 42 hrs now and its keeping DEAD accurate time. I have never been able to get these results even when I do service them....like what are the odds, did some kind of angel possess this watch or is this just something that happens???

  • Like 1
Link to comment
Share on other sites
alibababoombap Member

alibababoombap

Posted
Posted
On 1/9/2021 at 6:37 AM, saswatch88 said:

So check this out I had an elgin 539 a-11 hacking movement with a bad balance, i swapped the balance and realized it just did not work, (and yes i checked the hack lever, the stem was still in) I did nothing to this movement, didnt disassemble clean or do anything. I put the movement back in my organizer bin, and a couple days ago I opened it to start the service on it. However oddly enough as soon as I picked it up it started ticking away, so then I winded it up put a dial and hands on it and boom! This thing is still running! its been almost 42 hrs now and its keeping DEAD accurate time. I have never been able to get these results even when I do service them....like what are the odds, did some kind of angel possess this watch or is this just something that happens???

It's happened to me a couple of times, it's always the best feeling. But the real question is, have you tried wearing it yet? ?

Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
  • Author
Posted (edited)
1 hour ago, alibababoombap said:

It's happened to me a couple of times, it's always the best feeling. But the real question is, have you tried wearing it yet? ?

its a vintage watch which i normally dont wear them but i wore it for a few hours around the house until i went to bed and it was ticking away kept perfect time and was still good in the AM. New from the factory it had a 40hr power reserve it finally stopped at 45 hrs and was ahead by 1 min. but that 1 min happened after the first 40hr which iam going to chock up to the MS not having enough power since it was on it last leg causing low amp and high friction which would have sped up the watch in the final 5 hrs

Edited by saswatch88
Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
  • Author
Posted
Just now, saswatch88 said:

its a vintage watch which i normally dont wear them but i wore it for a few hours around the house until i went to bed and it was ticking away kept perfect time and was still good in the AM

 

2 hours ago, anilv said:

Probably some dirt in the movement which eventually move when you handled it again. I would clean and oil it and it should be fine.

Anilv

at this point iam leaving it as is, i feel like if i service. it it wont run as good

  • Like 1
  • Haha 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Chronograph Pusher Rod for EB8371-67 Snapped and Stuck in Button. Can't Unscrew.

      By watchweasol · Posted

      Hi. Yes I get it , the slot in the end I’d to allow you to screw the button on whilst holding the pusher shaft. To remove the pusher tube you will need a tool such as the one shown by Richard. I think Ali Express the Chinese Amazon has replicas of the Horotec system for a lot less money, how effective they are not having had to use one. But as you said the way to go is complete removal and replacement, bodging it up will  lead to a repeat failure
    • JohnR725
      Notifications

      By JohnR725 · Posted

      It does look like it seems to be working again I'm getting emails.
    • JohnR725
      30T2 adjustment of timing washers

      By JohnR725 · Posted

      One of the things that I've been bothered with lately is timekeeping? For instance a 90-year-old pocket watch what so to timekeeping was it supposed to keep? They publish railroad timekeeping but I don't know how well normal non-railroad watches were supposed to keep time. The reason why the question comes up for me is I spend a lot of time at work adjusting watches to keep really really good time  because I have to please my boss where as when the watch was made I have to wonder what kind timekeeping would've been acceptable. After all they typically didn't have timing machines 100 years ago and they were timing and six positions certainly not for the non-railroad grade watch. On the other hand I do get paid by the hour so maybe I shouldn't be concerned of how much time I Spend trying to make everything keep chronometer timekeeping almost. Citing a Delta of 40 seconds for a 90-year-old watch is quite outstanding.
    • JohnR725
      Is this pallet fork over-locking?

      By JohnR725 · Posted

      That's an interesting question which I don't think I've seen explained anywhere. But I think the problem will go away just about instantaneously. In other words the  coating is really thin and it should go away almost immediately. So the problem should resolve itself extremely fast.  
    • VWatchie
      Is this pallet fork over-locking?

      By VWatchie · Posted

      I experienced that different types of shellac and their ages are affected differently by IPA. Sometimes the shellac dissolves in a few seconds and sometimes several minutes are required. Nowadays I never let shellac come into contact with IPA. It's a hotly debated topic here on WRT if you search. Like John, I don't think you need to worry about the weight of the shellac, but instead that it might start rubbing against something. When I learned how to adjust pallet stones, I tried documenting my experiences in this thread. Hopefully, it can help you. I personally don't believe in the idea of abrading the epilame before oiling so I don't think you need to think or worry about it. The only time I've heard anyone mention this is Alex on the YouTube channel Watch Repair Tutorials but actually no one else. I'm not saying it's "wrong" just that I don't think it's necessary or adds anything.
×
×
  • Create New...