Jump to content

Anniversary Clock Running to Fast


Recommended Posts

Hi all and a merry xmas. I have a Kern anniversary clock which I have restored. The clock runs well however runs extremely fast despite turning the adjustment +/- clockwise fully. I have had a look at past forums and note that it might possibly be an incorrect sized torsion spring/wire. I believe the current wire in the clock has been replaced by someone previously based on finger prints found on covering sleeve. The pendulum weights (4) turn approximately 120 degrees. Is anyone able to advise if I am correct or an alternative idea to correct problem? Would appreciate any help including the correct sized spring and where to find/buy them. Many thanks for any help given2130923817_DSCN06311.thumb.JPG.32f25583dcd44cd5a975fc1c93f1c92b.JPG1790354123_DSCN06301.thumb.JPG.36a4fb5000f0a5afb9160be17805180c.JPG.

Link to post
Share on other sites

Hi If you can beg borrow or buy Charles Terwilligers book, the 10th edition  which is the bible on 400 day clocks, there is all the information you require, or as an alternative post a full picture of the back plate and members will be able to Identify the model and the spring type you require.

As Old Hippy said  the condition and length of the spring and its thickness and the positioning of the fork are critical to the operation              Happy New Year       all the best. 

 

Link to post
Share on other sites

Oldhippy is correct it will almost certainly be a suspension spring fault. Too strong or too weak results in running out of adjustment. It is possible to thin the spring if careful. The method is to lay the spring on a flat surface and carefully stroke the spring with a fine Emery ie 2000 grit to remove material. BUT you must not kink the spring in anyway. 

Link to post
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • As I indicated above I did email the best pictures that I could see of all the pictures and I'm pasting the answer below. To really go beyond we need better pictures. Then the definition a better pictures is the impossible picture? There's a reference to the roller table which is totally invisible at all these pictures. In the early days of lever escapement's there are lots of variations of things. So the roller table located underneath everything engaging with the lever might have something clever. If your watchmaker with a loop it's easy enough to look in. Photographing that would be quite a challenge unless you knew exactly what you're doing. Then attempting to remove the balance wheel would not recommend unless you have experience with watches of this type. As because removing the balance bridge does not allow you to remove the balance wheel without underpinning the hairspring. Typically the hairsprings are pinned to the main plate. You will notice the reference to conversion to lever escapement. As technology changed the early movements would transition into newer movements. So basically they will take their older movements and start to add bits and pieces of newer technology on to them rather than making an entirely new watches.     As for the fusee, I really can't make out any details about the escapement from those poor photos. It looks like a standard lever escapement but it has a verge style balance cock. The case marks look like London, 1830. This would be way too early for a standard lever escapement. Perhaps it started out its life as a verge and was converted to a lever at a later date. I'm pretty sure that the signature is James McCabe - a well known and collectible watchmaker. It would be interesting to see more details of the roller table. This could, for example, be a Massey lever. Better pictures would help.
    • Thank you aac58😊👍🏻
    • Hi    according to the list its a 108   manufactured in 78.  manual attached.      cheers 108 (2).pdf
    • Thanks watchweasol. I've had another look and it says the following at the bottom of the dial: Great Britain "46562 10878" JerseyMo, the plucky little watch isn't done yet. The auto-winding is definitely working. I've been checking in on it periodically and giving it a shake. It's ticking away as it should and the date advances, even if it's running about 12-15 mins slow over roughly a 12 hour period. I've warmed to it for sure. The bean counters can't mark this one off their spreadsheet just yet. Hello again Poljot. Is the "sophisticated" click just a piece of bent metal engaging the teeth? I think I'll have to investigate further and report back, after I've cleaned the DNA and grime from around the case back before I open it!  
    • Good evening guys! So after work right behind watchmaking desk. I did exactly as I sad. Once I’ve put it together and tiny tweak, here is result from all mighty Weishi No 1000. Think I leave it that way. One more time thanks for all inputs. Cheers
×
×
  • Create New...