Jump to content

Anniversary Clock Running to Fast


Konrad

Recommended Posts

Hi all and a merry xmas. I have a Kern anniversary clock which I have restored. The clock runs well however runs extremely fast despite turning the adjustment +/- clockwise fully. I have had a look at past forums and note that it might possibly be an incorrect sized torsion spring/wire. I believe the current wire in the clock has been replaced by someone previously based on finger prints found on covering sleeve. The pendulum weights (4) turn approximately 120 degrees. Is anyone able to advise if I am correct or an alternative idea to correct problem? Would appreciate any help including the correct sized spring and where to find/buy them. Many thanks for any help given2130923817_DSCN06311.thumb.JPG.32f25583dcd44cd5a975fc1c93f1c92b.JPG1790354123_DSCN06301.thumb.JPG.36a4fb5000f0a5afb9160be17805180c.JPG.

Link to comment
Share on other sites

Hi If you can beg borrow or buy Charles Terwilligers book, the 10th edition  which is the bible on 400 day clocks, there is all the information you require, or as an alternative post a full picture of the back plate and members will be able to Identify the model and the spring type you require.

As Old Hippy said  the condition and length of the spring and its thickness and the positioning of the fork are critical to the operation              Happy New Year       all the best. 

 

Link to comment
Share on other sites

Oldhippy is correct it will almost certainly be a suspension spring fault. Too strong or too weak results in running out of adjustment. It is possible to thin the spring if careful. The method is to lay the spring on a flat surface and carefully stroke the spring with a fine Emery ie 2000 grit to remove material. BUT you must not kink the spring in anyway. 

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Happy to have helped, great way to start the day with a win! 🥳
    • Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...