Jump to content

Movement Identification - Bovet


mcoulton

Recommended Posts

Hello

Does someone know what type of movement this is? It can out of a Bovet military watch but I don't think its a Valjoux or a Landeron. I haven't taken the dial off and looked on the other side of the movement.

Thanks in advance for any help that can be provided.

Michael

 

P1100298.JPG

Link to comment
Share on other sites

18 minutes ago, rogart63 said:

But i see a Incabloc spring. So must be shockproof . Never seen a FHF 70 with center second attachment? 

 Where?

 

19 minutes ago, rogart63 said:

But i see a Incabloc spring. So must be shockproof . Never seen a FHF 70 with center second attachment? 

 

Link to comment
Share on other sites

1 hour ago, rogart63 said:

But i see a Incabloc spring. So must be shockproof . Never seen a FHF 70 with center second attachment? 

Many variants to fhf70 with different bridge layout were made, namely inderctly driven min hand, then this with center second cock and your regular sweep second with min wheel incorporated inside ebauche. 

Its ancestor fhf30 and on, were mostly sub second versions.

Almost every manufacturer put some versions in their watches,  some were in-house and high grades , Rolex did too. 

 

  • Like 1
Link to comment
Share on other sites

Thanks to everyone for their responses. You've been a big help. Here are two more pictures of the time piece I'll be servicing. The crystal more than likely will need replacing as will the stem. I can't put any power into the movement as the click won't sweep fully to allow the crown wheel to turn.

Questions:  1.) Does my watch come with a seconds hand? I'm not sure if it does or if it uses a sub seconds which the dial doesn't accommodate.

2.) Are all seconds hands sized the same? I don't mean the length, I mean the pinion that they are secured to on the fourth wheel (?), is it the same for all seconds hands? Hope that makes sense.

3.) I'm thinking of buying an assortment of ETA watch stems, will I find a stem that fits this movement or do I need to search for a fhf70 movement specific stem. 

4.) What is the best parts source for this movement; Cousins, Gleaves London? 

Thanks in advance for any help that can be provided.

Michael

P1100301.JPG

P1100302.JPG

Link to comment
Share on other sites

11 minutes ago, mcoulton said:

1.) Does my watch come with a seconds hand? I'm not sure if it does or if it uses a sub seconds which the dial doesn't accommodate.

There appears to be a seconds hand pinion in the middle of the minute hand hub, and the movement shows a cock and tension spring for a center seconds pinion.

 

11 minutes ago, mcoulton said:

2.) Are all seconds hands sized the same?

No. You can measure the end of the pinion with a micrometer to determine the correct size.

17 minutes ago, mcoulton said:

3.) I'm thinking of buying an assortment of ETA watch stems, will I find a stem that fits this movement or do I need to search for a fhf70 movement specific stem. 

No. You will need the correct stem for this movement, which may be common to other FHF calibers in the same family, but very unlikely to be common with any ETA stems. If there is enough thread left on the broken stem you could use a stem extender.

19 minutes ago, mcoulton said:

4.) What is the best parts source for this movement; Cousins, Gleaves London?

Cousins certainly seem to have a comprehensive stock of FHF70 parts.

You may need to get a more positive ID for the movement. Ranfft lists the FHF 70 as a sub-seconds movement but yours has a sweep seconds hand. It is definitely part of the same family as the 70, but some parts will differ from the sub-seconds 70.

Link to comment
Share on other sites

Thanks very much for the responses. I believe the next step will be for me to dismantle the movement and have a look. I have a list of items I want to order from Cousin's and if I can figure out what I need from this watch then I'll include them in this order. 

Thanks

Link to comment
Share on other sites

Hello

I've stripped down this movement and have noted the markings. Can someone please clarify the type of movement based on the photo I provide? Is it a FHF I75 (as is i75) or a l75 (as in L75). I'm also having a little difficulty in figuring out the size for the second hand. I measure the pinion (?) at .30mm (second picture). Does that sound correct? 

 

Thanks

P1100326.JPG

InkedP1100358_LI.jpg

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
×
×
  • Create New...