Jump to content

Opening clock mainspring barrel


HectorLooi

Recommended Posts

 

This is the going barrel from a Forestville mantel clock. It is a bit strange. It has a couple of cogs attached to the arbor that doesn't seem to do anything. 

I am trying to get the barrel cover open. I've tried turning the cover anticlockwise but it seems stuck. I've sprayed WD40 and tried it again but nothing budges.

Any suggestions? ??

20201116_101751.jpg

Link to comment
Share on other sites

The cogs on top of the barrel are Known as stop work or Geneva stop works they allow the mainspring to be wound only so far they are designed to utilise the mainsprings optimum range of power delivery to the movement the spring can neither wind up or unwind fully thus eliminating the springs highest or lowest torque and evening out power delivery throughout the week.The stop works always rely on a certain amount of pre tension being put on the spring during fitting I can tell looking at yours there is non

Quite a few manufactures started using bayonet fitting great wheels on mainspring barrels instead of end caps do you have a photo of the other end of the barrel ? I would say it should twist apart try putting slight upward pressure on the barrel and slight downward pressure on the wheel as you twist.

Do you have a full picture of the movement it may help identify it because Forestville used a lot of European imported movements, from France, Germany and England.

Link to comment
Share on other sites

I'm familiar with Geneva stopworks. I've seen them on pocketwatch mainsprings. But this doesn't seem to be a Geneva stopwork because it doesn't have the missing cutout on one of the wheels. Besides, Geneva stopworks only allow about 300° rotation of the arbor. This would not be sufficient for a 8 day movement. 

I didn't take a photo of the movement as package was obviously dropped during transport and the foot of the casing was broken off. The movement was partially pulled off the mountings. I took the movement apart to check for damage but it appears to be ok as it was still ticking away.

The movement is German made and it says "Suevia Sidelfingen".

 

20201104_123200.jpg

20201104_123207.jpg

20201104_123250.jpg

Link to comment
Share on other sites

There are different types of Geneva stop works, this type is most common and the main thing it is for, it prevents the arbor from becoming detached from the spring. First thing is to remove the fitting from the arbor. Put the key winding arbor into your bench vice, if it is a smooth jaw its fine if not you need plates to cover the jaws because you do not want to mark the arbor, turn the barrel with you hand as if you are winding it and remove the pars that are over the arbor, when removed slowly let the spring unwind through your hand until all the power is off. Then do this.   The wheel green arrow is detachable by moving it away from the red arrow part.

20201116_101751.thumb.jpg.cbcb88fa946b9f2718e5e2f4be889254.jpg

Link to comment
Share on other sites

Ok. If that's the case, then with only 1 turn of the mainspring, the power reserve would probably last only 1 day.

Is there any harm in not having a properly working Geneva stopwork, other than erratic time keeping?

Should I try doing a tooth repair or cut a new wheel?

Link to comment
Share on other sites

I've been studying the mechanism of this stopwork and found it devilishly ingenious. There is one extra long cog on the smaller wheel and the bigger wheel has one groove that is shorter. So the arbor can be wound almost 8 complete revolutions before the long cog would contact the short groove and come to a stop.

I think I'll try straightening the bent tooth and braze another piece of brass on top of it to reinforce and stop it from bending again.

Thanks again OldHippy. Your guidance is most helpful.

Link to comment
Share on other sites

When you put it all back together, wind some power on the spring before putting the center stop piece in, then put it in the "stop" position (stop for unwinding). 1/2 turn is a general rule; what you really want to do is wind the spring fully without the stopworks to see how many turns of wind the spring develops. Typically this is about 6 or 7, but some clocks can be more or less. Very old clocks I see here often develop about 5 turns, and have stopworks that permit about 3-1/2, some modern ones from this area (Le Castel for example) do about 15 full turns of wind. You want to set up the stopworks so that you are using the middle part of the spring, so if you get 8 turns with that stopwork, and the spring develops 9 turns without, 1/2 turn of pre-wind is good, actually slightly less than more if you see things don't want to line up at 1/2.

 

Stopworks help use the most even part of the mainspring's power, but also keep a lot of stress off of the hook and end of spring where it attaches to the barrel.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Its probably stronger now then it has ever been. The brass and steel in these types of English & German clocks are not that hard that is why you find normally loads of re-bushing and pivots worn. There are a few exceptions in the better types of movements. 

Link to comment
Share on other sites

I always take it easy when approaching the end of winding to avoid unnecessary strain. That includes fusee stop arms as you can literally rip them off the main plate if you wind too hard. 
 

The same applies to releasing the pressure of the winding key, each time you wind. It’s not necessary to suddenly release the key and hit the train and click spring with all of that force at once. 

Link to comment
Share on other sites

After removing the cover, the teeth of the great wheel are no longer on the barrel. The smooth barrel tends to slip when I'm trying to wind the spring.

I tried tightening a hose clamp to the barrel. This gives me a better grip, but even through thick gloves, it really hurts the hand. Is there a better way to hold the barrel?

20201122_081136.jpg

Link to comment
Share on other sites

Wear a thick pair of gloves when removing springs. This is the type of winder I have. 

 

If you put a hoop around you will only be able to fit it so far, the cracks show where the wheel fits. That is why I suggested solder. In an ideal world a new barrel should be made.   

download.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...