Jump to content

Movement holder

Graziano

By Graziano
in Tools & Equipment

 Share

Recommended Posts

Graziano WRT Addict

Graziano

Posted
Posted (edited)

Hi all, I have been using this Meyers movement holder no58 that I perchased here in Australia for a while now and I must say, they don't make things like they use to. It's easy to set up and it holds all movements regardless of sizes, shapes or form. I have a Seiko 6309 plate in there that I just jeweled the barrel arbor port in there and the other movement plate is an omega 485 ladies movement plate. It has 4 different clamps that slide in and a quick release button where my finger is. It does not rock or come loose. The movements have no sharp corners intruding into the plate because the clamps are rounded. I have about 10 different movement holders including bergeon and this beats all hands down. What do you think? 

IMG_20201107_200007.jpg

IMG_20201107_195717.jpg

IMG_20201107_195439.jpg

IMG_20201107_195406.jpg

IMG_20201107_195341.jpg

Edited by Graziano
  • Like 4
Link to comment
Share on other sites
Tudor Distinguished Member

Tudor

Posted
Posted

I have grown to appreciate dedicated movement holders. 

The ones I can’t buy, I just make. 

But this design looks much better than the burgeon one I have (and no longer use). With four points of contact, it always seemed to be putting pressure where I didn’t want it, or blocking something.  

  • Like 1
Link to comment
Share on other sites
Graziano WRT Addict

Graziano

Posted
  • Author
Posted
6 hours ago, Tudor said:

I have grown to appreciate dedicated movement holders. 

The ones I can’t buy, I just make. 

But this design looks much better than the burgeon one I have (and no longer use). With four points of contact, it always seemed to be putting pressure where I didn’t want it, or blocking something.  

Yes that's what I am talking about. As soon as you take the balance out especially ladies movements the corners of the bergeon slip into plate and it shifts around loosely. One other movement holder I use is the old marshal one with rounded plate clamps as in the photo below. 

16048201102615645430692049708400.jpg

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
On 11/7/2020 at 5:16 AM, Graziano said:

Hi all, I have been using this Meyers movement holder no58 that I perchased here in Australia for a while now and I must say, they don't make things like they use to. It's easy to set up and it holds all movements regardless of sizes, shapes or form. I have a Seiko 6309 plate in there that I just jeweled the barrel arbor port in there and the other movement plate is an omega 485 ladies movement plate. It has 4 different clamps that slide in and a quick release button where my finger is. It does not rock or come loose. The movements have no sharp corners intruding into the plate because the clamps are rounded. I have about 10 different movement holders including bergeon and this beats all hands down. What do you think? 

IMG_20201107_200007.jpg

IMG_20201107_195717.jpg

IMG_20201107_195439.jpg

IMG_20201107_195406.jpg

IMG_20201107_195341.jpg

Just picked one of these up on eBay. Hope it is worth 75 bucks

Link to comment
Share on other sites
Graziano WRT Addict

Graziano

Posted
  • Author
Posted
9 hours ago, jdrichard said:

Just picked one of these up on eBay. Hope it is worth 75 bucks

Hi there Mr jdrichard it is a brilliant holder, let me know what you think when you try it out. Did you get the complete set of sides? There should be 4 pairs. Holds all size and shape movements. Yabbadabbadoooo! 

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
1 hour ago, Graziano said:

Hi there Mr jdrichard it is a brilliant holder, let me know what you think when you try it out. Did you get the complete set of sides? There should be 4 pairs. Holds all size and shape movements. Yabbadabbadoooo! 

I believe it is complete but have not yet received it. I also purchased the Marshall movement holder that is on this post as I am sick of the current crappy movement holders. Poor engineering. So BAM! I will now have the best:)

  • Like 1
Link to comment
Share on other sites
  • 7 months later...
jdrichard Distinguished Member

jdrichard

Posted
Posted

Update. Picked you another Meyers #58. These are the very best for all watch work and especially for pocket watches. I now have two, yes 2, of these.  Bought this one on eBay and it was dirty as heck. Ultrasonic cleaning then my buffing machine then a lot of elbow grease and tada.

 

11F9CAE7-1550-4A7F-90C8-B18A29218A5D.jpeg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...