Jump to content

My Oris for repair

kabong

By kabong
in Your Watch Collection

 Share

Recommended Posts

kabong Member

kabong

Posted
Posted

I have no recollection of buying it, but I must have picked it up a watch fair in Birmingham for 5 or 10 pounds. It winds a bit and runs a tiny bit.

Once I finish the watch course then I will attempt to get this watch working.

I really like the styling so will attempt to fix it, but I guess it was cheap at the fair for a reason... probably unrepairable!

20201027_144341.jpg

  • Like 2
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
17 minutes ago, kabong said:

I really like the styling so will attempt to fix it, but I guess it was cheap at the fair for a reason... probably unrepairable!

More than likely it just needs cleaned and serviced. I've seen quite a number of good looking watches get discarded, simply because the owner is not willing to pay to get them serviced.

 

  • Like 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Vintage Oris is collectable, specially if the movement is in-house.

Judging from the subsecomd this is an in-house and when in good running condition should fetch aprox $ 200, depending on the condition of the bezel, specially back of the bezel for wear due to swet of wrist,  it is worth more if bezel is in good shape.

Dial is in decent conditon, check dial feet.

Caliber is engraved on barrel bridge. 

Oris did use swiss calibers made in Asia.

Check for price on ebay as only the ones in excellent aesteic shape fetch considerably more, Genuine Oris crowns are signed.

No matter what is wrong under the hood, it is fixable.

 

 

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
1 minute ago, kabong said:

As a noob can you explain the brave bit please?

456KIF came in 7 & 15 jewels versions, I see little improvement to be gained by adding 8 jewels whilst the escapement remained the old pin pallet in 15 jewels variant too.

Jewels brought lots of improvement to watches, there for couple of decades whoever put more jewels in the movements attracted more customers.  jewels with no technical significance were added to the movement, whereas remaking a jeweled escapement was costly. 

 

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      I did not. I thought about it, but I had cleaned it in my ultrasonic, and the tech sheet shows lubricating it in place already assembled, so I figured discretion was the better part of valor. Although since I have to depth the jewels anyway, maybe I pull the pinion off to rule it out 100% as part of the problem. Do you know if there's a safe way to do it? I don't want to use a puller because it would push down on the plane of the wheel, and that seems like a Bad Idea. I thought about using a roller table remover, but I don't think I have a hole stake pointy enough to push it down.
×
×
  • Create New...