Jump to content

Seiko Kinetic


Timpress

Recommended Posts

Hi. I have a Seiko Kinetic. About thirty years old. It stopped about three years ago. I sent it away and the battery was replaced. (I didn’t even know it had a battery.) Now it is starting to go again, with the second hand ticking two seconds at a time. I’m surprised – and wonder if it is the same problem, or a different one (eg, capacitor). I would prefer to send it to someone who know what they are doing, but how to go about finding such a person? Or should I tackle it myself?

Link to comment
Share on other sites

Hi   It is possible to change the capacitor/cell with a few tools,  we need pictured of the watch movement to determine the make and if possible the caliber number,   capacitor /cells cost approx £10 depending on make.

A watch of 30 yrs has done well but deserves a chance.

Link to comment
Share on other sites

Hi  the model is a seiko 5M42A and I have attached th tech sheet for you as it contains a lot of important information should you decide to do it youself.  also attached id the capacitor.cell list for all the relavant models. this will give you a fighting chance with the DIY option.       good luck.       cheers

Seiko 5M42A, 5M43A.pdf Batteries - Seiko Capacitors (2).pdf

Link to comment
Share on other sites

The original storage cell in Seiko Kinetic movements was I believe a capacitor, the new replacement cells are a lithium polymer rechargeable battery. 

The new batteries have a much higher capacity than the original capacitors which has two consequences, the first of which is that from fully charged it can last months of static storage before the watch stops, the second of which is that it takes a lot more movement to charge it up and so takes longer to get it out of the 2 second tick zone.

You may need to do an extended period of charging exercise to get enough power into it in the first place but once there you should be fine.

If the problem persists though you may want to check the free running of the rotor as if this gets tight charging efficiency will be impared.

  • Like 1
Link to comment
Share on other sites

Replacing the capacitor on this watch is not difficult, provided you have the basic tools of a reasonable quality, and the confidence to use them properly. 

1)Separate the strap.

2)Remove the case back.

3)Unscrew the rotor retaining screw.

4)Remove rotor and drive wheel.

5)Unscrew the two screws that retain capacitor cover.

6)Remove capacitor cover and insulator.

7)Remove capacitor.

Reassemble in reverse order.

Problems you may encounter include:- 

trying to find one or both of the loose capacitor retaining screws (escapology on a par with Houdini at his best!!).

maintaining the lightweight thin plastic capacitor insulator in the correct position whilst reaffixing the retaining cover.

Hope this is of help.

 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...