Jump to content

Jacot tool and pivot file burnisher question

clockboy
 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted (edited)
1 hour ago, Tmuir said:

The other gauge is part of the jacot tool, its for measuring the size of the pivot, I agree that the rubber bands are not for the jaccot tool

My eyesight lets me down again.:biggrin:My brain lets me down too.

Edited by oldhippy
Link to comment
Share on other sites
  • Replies 262
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

JohnR725
JohnR725

Thinking about a perfect finish here's an interesting PDF to read. A Quick Evaluation of Surface Finish of Pivots.pdf

luiazazrambo
luiazazrambo

I have recently used a jacot tool to successfully re-polish a badly worn pivot in a pocket watch the first time in my life. I have watched Richard's videos about it and I also went to a book printed i

rodabod
rodabod

The burnisher removes a small amount of material. But that is not it’s purpose. It’s purpose is two-fold. It folds over the surface grains of metal which makes them smooth and achieve a polish. So thi

Posted Images

  • 9 months later...
Tmuir Distinguished Member

Tmuir

Posted
Posted

I've got a Unitas 235 that has a cracked jewel that also damaged the pivot on the third wheel.

Cousins still has replacement third wheels for this movement, so safe with the knowledge I can order a repalcement wheel I decided it was time for me to try and polish the picot with my Jacot tool.

I've polished pivots on clocks no problem, but this is the first time I have tried on a watch pivot.

I'm amazed at just how much harder it is to polish the pivot on a watch.

I've butchered the pivot enough that I will be ordering the replacement wheel, but will continue to polish this pivot now just for practice.

The few things I have learnt from my attempts so far are.

  • Check the pivot dimension closely and select the correct diameter slot on the Jacot tool, don't just go 'close enough'
  • Ensure you have set up the tool so there is no slop in the way it is holding the wheel, else the wheel will tilt by a degree or 2 as you move the bow and burnisher backwards and forwards making it easier to end up with a tapered pivot
  • Take care on how you hold your burnisher to make sure its parallel to the pivot.
  • Get yourself a few wheels to practice polishing pivots from junk movements before touching an important wheel
  • Give yourself a break and go read WRT if you feel your pulse rising. :D

I may of done a crap job on polishing this pivot, but atleast I can say that I've started to learn how to use my Jacot tool now.............

  • Thanks 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Working with such a tool for the first time, you are going to make mistakes. Just working with a bow is an art in its own right. Knowing where you went wrong and correcting is part of the fun. You will get there in the end so just keep it up.

  • Like 1
Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I went back last night and practiced some more. I got better results, but still not good enough.

I'm leaving it like that until I receive the replacement wheel and confirm it fits, because if it doesn't I will be taking it in to my night class and asking for help before I ruin it.

But once I'm sure the replacement wheel fits I will continue to practice on this one until I get it correct.

I also just received today a trashed English leaver fusee movemt that I only paid $20 for. Its too far broken to ever be made a working timepiece again, but will  prove me plenty of learning potential on a type of watch I've not touched before.

Far better to learn on a $20 wreck of a movement that a several hundred dollar good example.

 

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
margolisd WRT Addict

margolisd

Posted
Posted

Hi folks. I just got a Jacot tool from eBay. I'm working through Practical Watch Adjusting by Donald de Carle which has been a brilliant guide. Just a couple of things I'm not sure on.

First, can anyone explain the scale on the pivot measuring tool? Why are the numbers on the left and right side different? I don't see how they relate.

Also, can anyone explain how to secure the work piece to the tool? The ones I've seen on YouTube have two "snake teeth" that clasp the wheel but this only has one. I can't see how it can hold anything securely.

Thanks all.

IMG_1033.jpg

IMG_1032.jpg

IMG_1034.jpg

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

I have never used that type of gauge for pivots, so I don’t know about the measurements. I know you slide the pivot along on the inside until it stops and you read off the measurement.

 

Here is a good video about how to set up a Jacot tool and use it. Working with such a tool takes a lot of practice. Do not start on something you wish to keep, wait until you have the skill.

 https://www.youtube.com/watch?v=f-8Vd2m-WBs

  • Thanks 1
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

As you say, there are two sets of numbers on the gauge. 

I'm sure the left hand set of numbers is the diameter of the pivot in Dousiemes, and the right hand set is the appropriate Jacot drum notch that you should use when working with that pivot.  To check this, measure the gap of the gauge at the relavent numbers and see if it corresponds with the sizes I have given.

Here is a conversion of Dousiems to Millimetres.

1 = 0.19

2 = 0.38

3 = 0.56

4 = 0.75

5 = 0.94

6 = 1.13

7 = 1.32

8 = 1.50

9 = 1.69

  • Thanks 1
Link to comment
Share on other sites
margolisd WRT Addict

margolisd

Posted
Posted

Ah. Actually the scale on the left is metric. But I think you're correct about the scale on the right showing which drum notch to use. Mystery solved. Now if I could just attache a balance wheel to the thing. I still can figure out how the "snake tooth" secures it. Thanks Old Hippy for the YouTube link. I had actually watched that one and it's super helpful. Although he doesn't demonstrate on a balance wheel which I understand should have rounded pivot ends. That seems to be a real skill which is going to require a lot of practice.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

The shaft is located between the hollow centre of the driving wheel and the shoulder of the pivot at the jacot end.  The driving dog sits between the the spokes of the wheel to impart the driving force.  Nothing is clamped in place.

  • Thanks 1
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

The little slotted gages are kind if sketchy, one of my teachers called them "pivot breaking tool". But for small diameters, say under .13mm or so, a micrometer poses a real threat of making tiny flats on the pivot even with a very light touch. Best is jeweled hole gages, available in .01mm, .005mm, and .0025mm increments. Without those you can get close using a micrometer and then use the actual jewel as a gage, look for about 5° of "tilt" for the correct freedom.

The drive finger is often a pair but a single one works fine.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
The little slotted gages are kind if sketchy, one of my teachers called them "pivot breaking tool". But for small diameters, say under .13mm or so, a micrometer poses a real threat of making tiny flats on the pivot even with a very light touch. Best is jeweled hole gages, available in .01mm, .005mm, and .0025mm increments. Without those you can get close using a micrometer and then use the actual jewel as a gage, look for about 5° of "tilt" for the correct freedom.

The drive finger is often a pair but a single one works fine.

Need to buy a jewel gauge ruler and a set of pin gauges.c09c8b255244f0ef7d63e38d2c4abf84.png574eae8cbc88d997ecdbe8e68c71a102.png


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      As an experiment i was thinking of not hardening it to see how it fairs. Now that i have a complete template i could knock up another in half the time if this loses its elasticity. I might play about with a few pieces today to test their bending and spring properties. This was cs 100 the supplier quoted in annealed state, it was nice to work with files so I'm taking it thats its state. What you are looking seems like it would need annealing to work it. This is why i went for this stuff that cuts out that process, it was so easy to work.
    • dnhb
      Is this a 'hack' ?

      By dnhb · Posted

      Showing state of hairspring on receipt, backplate & 'dished' wheel. 
    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      I would harden and temper (to a light blue). It's so easy to do and only takes a couple of minutes. A search on ebay UK for "spring steel strip cs" finds plenty available in small quantites and thicknesses from 0.1mm up.  But the question is ( @nickelsilver) which "CS" number is best for watch parts ?  Also, from one of the ads : "CARBON SPRING STEEL. SIZE IS METRIC 15.00mm X 0.10mm X 304 MM  CS100 FINISH BRIGHT . HARDENED AND TEMPERD TO 480-530VPN" I've no idea about 480-530VPN. Does that mean it needs annealing before working?       Have you seen this video, he shows how to determine where the indents go ?  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      Here is the insert ring for rectangular or elliptical movements: Note that the length is the side with the stem cut out on the spreadsheet (in the picture below this is 15.15: Here is the fake pdf file, again you need to convert to .zip after download to access the FreeCAD and 3mf files. Rectangular insert disc.pdf    
    • JohnR725
      Omega cal. 565 - low amplitude

      By JohnR725 · Posted

      as you took the mainspring out what did it look like? It's amazing how much amplitude you can get if the mainspring actually has the proper shape. last week I was doing a 12 size Hamilton and was very much surprised with the beautiful back curvature the mainspring had. Then the watch had a really nice amplitude the group would be so proud it was 350 until I dropped the lift angle down to 38 that drop the amplitude quite a bit below 300. then with the beautiful back curve it still had really nice amplitude the next day. I really wish all my mainspring's look like this as the watch had beautiful amplitude the next day. So many of the aftermarket pocketwatch Springs I see now do not have anything resembling a back curve may be a slight curve and that's about all. They still work but they just don't work as nice as a properly made spring. then Omega as all sorts of nifty technical documentation unfortunately every single corner is watermarked with where it came from who downloaded it etc. very paranoid company. On the other hand I will snip out images like from the document on recycling a mainspring barrel. for instance here's the section on what your mainspring should look like. water damaged a lot of times means rust was there rust on this watch?
×
×
  • Create New...