Jump to content

Dial feet repair - All techniques


Recommended Posts

  • 7 months later...

Can anyone advise?

I got given a cheap ebay Seiko 7009a for my birthday a while back to play with. Not in the best of conditions but I usually stick to pocket watches so this was something to play along with. I've got it running again after changing the balance and cleaning out the lower pivot jewel and am now looking at the dial. It has no dial feet but I can see where they were originally on the back. They're right near the edge and on the dial side, the chapter ring covers the edge so any heat damage would be covered. 

I saw one of Balogh's video's and thought I'd may as well have a try. The dial is brass so I cleaned up around the original foot position with a file. I have some 0.6 mm copper wire and was using electrical flux and solder but I can't get the two to stick together. Can anyone suggest anything? Different flux or solder maybe?

Link to comment
Share on other sites

On 07/10/2017 at 12:07 PM, mistergrumpy said:

Can anyone advise?

I got given a cheap ebay Seiko 7009a for my birthday a while back to play with. Not in the best of conditions but I usually stick to pocket watches so this was something to play along with. I've got it running again after changing the balance and cleaning out the lower pivot jewel and am now looking at the dial. It has no dial feet but I can see where they were originally on the back. They're right near the edge and on the dial side, the chapter ring covers the edge so any heat damage would be covered. 

I saw one of Balogh's video's and thought I'd may as well have a try. The dial is brass so I cleaned up around the original foot position with a file. I have some 0.6 mm copper wire and was using electrical flux and solder but I can't get the two to stick together. Can anyone suggest anything? Different flux or solder maybe?

Hi, I use solder with flux already in it, I have always found that using a separate flux it tends to burn off to quickly. I would also tin the area on the brass and on the copper first as well by putting solder on it and this will aid the flow of the solder when you try to make the join. It could also be your soldering iron is not upto the job as the brass will be acting as a heat sink, again I use a temperature controlled soldering iron that you can turn up to compensate. Hope this helps.

Link to comment
Share on other sites

On 2017. 10. 13. at 1:50 AM, PJA said:

I've found this video for a pocket watch, but it might help with some sort of how to go about it as well. Just in case it's not too late.

You just found my video again  :D

On 2017. 10. 13. at 3:31 AM, vinn3 said:

i reccomend "tining"  for most soldering jobs.   with watch dials ,  pin locating and  overheating the dial are the big problems.   vin

Above i am shiwing an easy method how to find the point ;)

  • Like 1
  • Haha 1
Link to comment
Share on other sites

7 hours ago, szbalogh said:

You just found my video again  :D

Above i am shiwing an easy method how to find the point ;)

It seems that you are putting these videos to teach us and I'm pointing them to those who need them, so in a way, we're teamed to help when possible.

Link to comment
Share on other sites

  • 1 month later...

hi everyone!
I feel that people are still hesitant about the price and the difficulty of operating the dialer.
Recently I found a good seller with good price, it combines tin paste very easily
I bought his 220v version, I started work pretty easily and quickly than any video I have seen before.
My friend bought another one on ebay for $ 230 which did not include shipping cost and compared to the new one I bought really different electricity,
I bought the current can be twice as strong, solder quickly about 2 seconds
Due to the use of tin paste, the solder is quite beautiful and does not have too much tin.

 

This is the link he sent me 

 

 

Sorry i used gg tránlate.

  • Thanks 1
Link to comment
Share on other sites

a timely topic revival...i've thinking how i would make a resistance solderer for dial feet for a current project

For you experience guys, would you say the two posts (feet) are always 180 degrees apart, ie a line through them also goes through the centre.....or are they sometimes offset, ie a line through them would be part of a chord?

I've been think that as well as making the solder joint, some sort of position would be nice and how to do so will depending on the answer to the above.  I can imagine the frustration at getting a perfect solder joint only to find the pins don't align with the holes.

Edited by measuretwice
Link to comment
Share on other sites

19 hours ago, Cougarnaut said:

No, the positions can differ, I solved the problem like this: http://dirkfassbender.de/dial-feet-position-gauge.html

 

 

thanks......random locations complicates things but I suppose its to be expected.  Can you comment on how the your fixture is used.  I see from other posts you are soldering, but am unsure how the set up goes from locating with plastic arms to soldering without the plastic arms

Edited by measuretwice
Link to comment
Share on other sites

Hi all,

I have a dial with broken feet, unfortunately.

I read most advice to resolder them with a special welding machine, which I don't have, and could potentially cause a spot on the dial due to overheating.

So I keep searching and I found some advice the use of JB weld, a specific 2 components glue.

Does anybody have experience on this glue?

Thanks a lot in advance

Link to comment
Share on other sites

22 minutes ago, Massimo said:

 

Hi all,

I have a dial with broken feet, unfortunately.

I read most advice to resolder them with a special welding machine, which I don't have, and could potentially cause a spot on the dial due to overheating.

So I keep searching and I found some advice the use of JB weld, a specific 2 components glue.

Does anybody have experience on this glue?

Thanks a lot in advance

Are you working on a Seiko 5 or similar? use thin bi-adhesive tape and place some on the movement ring. Or get "dial pads" which in practice are the same thing. Gluing is unlikely to be effective.

Link to comment
Share on other sites

Are you working on a Seiko 5 or similar? use thin bi-adhesive tape and place some on the movement ring. Or get "dial pads" which in practice are the same thing. Gluing is unlikely to be effective.
Thanks Jdm,
Indeed it's a 4r36, seiko 5.
I honestly dislike the idea of the double side tape... As a concept.
I agree it is fast, easy, and (temporarily) effective, without risk of damage.
But in the long term it might move.
Additionally the feet are kept in a plastic hole by interference, without screws so it must be a good bond if I want to reattach them.
Link to comment
Share on other sites

3 minutes ago, Massimo said:

Indeed it's a 4r36, seiko 5.
I honestly dislike the idea of the double side tape... As a concept.

I agree it is fast, easy, and (temporarily) effective, without risk of damage.
But in the long term it might move.

Additionally the feet are kept in a plastic hole by interference, without screws so it must be a good bond if I want to reattach them.

It will not move, and the concept of repairing is to get the job done, not being purists on a $70 watch.

Anyway, exactly because the feet are a tight fit in the ring, they will stress the gluing point and break it, just like it broke the original soldering. So you will have to make the glue blob bigger, now it will push on the ring and the dial won't be flush. Then you start reaming out the hole the ring to make space... lot of effort for a patchy job that is the end is worse than adhesive tape. But I guess that not having been there before you'll need to experience first hand... have fun :biggrin:

  • Like 1
Link to comment
Share on other sites

1 or 2 people were swearing by that JB weld for attaching new dial feet at one point on the forum, but when I tried it i found it was only a shade less than completely useless, I don't know if I'm doing something wrong but I've never been able to get any kind of cement to bond properly between the replacement copper dial feet i have and the dial, always snaps off without barely any effort.

I think short of special, costly welding equipment you have to accept that dial dots/strips are your best shot, it's the kind of thing that irks most repairers, we all want a better way of doing it i think, but it usually works out okay, at least if the movement ring is a fairly tight fit in the case. 
 

  • Like 2
Link to comment
Share on other sites

Hi all,
Thanks a lot for the support, indeed I have the original pins but it's clear that the contact surface, using even a good glue, is too small.
Maybe using that feet with a larger head could help, increasing the area of contact.
I'll order both and give it a try.
Fingers crossed...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
    • Hands up all those who voted to leave the EU 😂, oopsie.  UK has just signed the Hague convention, next year that will provide cross border clout to British courts.
    • Ive heard about that oil before for the lever pins. I found it easy to work on , it didn't have a whole lot of pivot wear but i bit sloppy on the lever cock, i think you have to live with what you have or bin it. Stiff to wind and set ?  Not a cannon pinion issue that has no friction thats made up further back and if I remember the barrel drives the hour wheel. No problem on this one .Let me know when you start it as i have another that donated to this one, i can work alongside you with it, two heads are better than one. 
×
×
  • Create New...