Jump to content

Quality Movements With Parts Available???

les13

By les13
in Watch Repairs Help & Advice

 Share

Recommended Posts

les13 Member

les13

Posted
Posted

I am sure this question has been asked before, but it is a question that could be asked in many different ways.  Anyway, I did not find anything from searching.

My primary interest is American made wrist watches made before the '60's.  I am a newbie and have been buying cheep Hamilton, Elgin, etc. movements and trying to repair them.  If I need a part, they can sometimes be difficult to find.  I started out in Mark's classes with the Seagull 6498 clones.  If I broke a part, which I did regularly, it was difficult to find replacements.  My question is what are your recommendations for reasonably priced watches in which parts are generally readily available.  Of course, I am looking for mechanical watches with minimal complications.  Movements that would be suitable for a newbie to tackle.  Is there such an animal?  I am not looking for cheap movements, but I would like to keep a sanity check on how much money I spend on this hobby.

Thanks for your help.

Link to comment
Share on other sites
Klassiker Distinguished Member

Klassiker

Posted
Posted

I can't recommend any American movements, but there are a lot of Swiss or German ones from the 50s or 60s which we're made in large quantities and for which you can easily and cheaply find spares or donors. They we're built to be serviced too, which makes them fun to work on. I'm thinking AS, Osco, FHF/Standard, Peseux etc.

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

You can always find ST96 (mumbi special) from India, since they still are made in India and widely used there. 

You can get two watches for the price of a seagul movement.

I think the reason Mark uses seagul is wide availability and newness, so you wont be spending more time on finding a movement and cleaning than actual learning of the lessons.

ST96 in manual wind, easy to work on, yet higher quality than chinese.

Should expect a home made dial in the case though.

 

 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...