Jump to content

LUCERNE SPORT CHRONOGRAPH LUME?

Stevelp

By Stevelp
in Watch Repairs Help & Advice

 Share

Recommended Posts

Stevelp Watch Enthusiast

Stevelp

Posted
Posted

Hi everyone, I hope everyone is well!  So its time to move on to another project and this Lucerne Sport Chronograph has caught my eye.  When it comes to older watches I tend to be a little hesitant when it comes to lume.  I know if you're careful and respect it, radium shouldn't be an issue but I've decided just to leave them alone.  In regards to this watch I do see a "T" to the left of "SWISS", so this to me means Tritium, but there is no T on the other side of "MADE".  Also the color seems a bit off to me for tritium but that I guess could change from one manufacturer to another.  I think the one "T" should be enough for me but I thought I would touch base and see if anyone would know for sure what the lume material is on these watches.  Thanks!

LUCERNE.jpg

Link to comment
Share on other sites
Tudor Distinguished Member

Tudor

Posted
Posted (edited)

I'd bet it's Tritium. Radium had no markings that I've ever seen. And Radium tends to be much darker at this point.

Geiger counter will tell you for sure, but I wouldn't hesitate to work on it personally. Most of my watches and projects are Tritium.

 

EDIT_ hands look to have been re-lumed at some point. Do they still glow?

Edited by Tudor
  • Like 1
Link to comment
Share on other sites
Stevelp Watch Enthusiast

Stevelp

Posted
  • Author
Posted

I agree that it is likely tritium.  And as far as the color you are right, radium does tend to be fairly dark, even black at this point on some watches that I've seen.  Also the lack of radium burn on a light dial points me in the direction of tritium.  As for markings for radium, some dials do have an "RA" marking on each side of the "SWISS MADE" just as it would "T" for tritium. 

Link to comment
Share on other sites
Stevelp Watch Enthusiast

Stevelp

Posted
  • Author
Posted

It's definitely nice when they mark it, takes the guess work out of it.  I haven't seen it very often but it is out there.  After radium was phased out Promethium was also used for a short time.  I haven't seen one of these dials in person but those were marked with a "P" or "PR".  Huh, that is interesting.  I haven't paid much attention to newer watches, but that's nice they're doing in.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • RichardHarris123
      Any tips to correct a sloppy error?

      By RichardHarris123 · Posted

      Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
×
×
  • Create New...