Jump to content

Smiths Sandiville Mantel Clock


HectorLooi

Recommended Posts

20200817_111329.thumb.jpg.a31731484178d4a4f6186c2b1cf66f07.jpg

 

Just received my Smiths Sandiville mantel clock a couple of days ago.

Quite good condition generally but not running. The Westminster chime is all messed up also. This will probably keep me busy for a few weeks.

There is another clock that just came up on ebay. It's for a good cause too. Proceeds go to East Anglia's Children Hospices. Really tempted to get this also. Unless one of you guys outbid me. :thumbsu:

https://www.ebay.com.sg/itm/Art-Deco-Mantel-Clock-Smiths-With-Chimes/402360864848?hash=item5dae939050:g:-wsAAOSwAHlfNAfW

Link to comment
Share on other sites

I got the clock stripped down to the 3 gear trains. Tomorrow I'll separate the plates and remove all the wheels.

What would be a good cleaning solution for clocks? I've used dishwashing liquid and turpentine before. Ended up removing a lot of lacquer from the brass. 

If I decide to polish and re-lacquer the plates, how do I go about doing that? 

20200820_210814.jpg

Link to comment
Share on other sites

Hi Hector  depending on how dirty the movement is   I usually give it a good scrub down with either Petrol  or white spirit and oil.  The old way of polishing the plates was with a brush charged from a chalk block (still available)  when dried and pegged out.     all bearings/pivots checked . Reassemble and lubricate with Windles clock oil  its the best .     all the best.

  • Thanks 1
Link to comment
Share on other sites

Yes I have a Webster.

But while adjusting the retainer ring, disaster struck. The end of the mainspring slipped off the barrel hook and slipped into the ring. Now I don't know how I'm going to get the mainspring out without the end of the spring sticking out. :phew:20200821_222715.thumb.jpg.25ff7b131188f0811ef8e2d8b0eeaef9.jpg

Link to comment
Share on other sites

Yup. All there. Thanks.

I've cleaned everything and am ready to reassemble. I noticed that on the chime train, there are 2 wheels with a pin sticking out. Do I need to align or synchronize these in any way?

20200823_230820.thumb.jpg.5d51122c776878feac2bbc859e477669.jpg

Do clocks have tech sheets like watches, like the ones watchweasol always supplies so generously?

Link to comment
Share on other sites

Make sure this wheel is about in this place, the same on the strike side, you will probably need to  make adjustments when all the wheels are fitted. On the strike side the hammer lifting lever needs to be away from the star wheel, that is the one that lifts the hammers. 

20200823_230820.thumb.jpg.5d51122c776878feac2bbc859e477669.jpg

  • Thanks 1
Link to comment
Share on other sites

I managed to get the going train running again last night. It was still going this morning despite the broken suspension spring. 

I will work on the chime and strike tonight.

I now find clocks so much more interesting than watches. There are so many different types. They are less strain on the eyes, no need to get on your hands and knees with a magnet in one hand and a flashlight in the other. No need to wait for a "shake free" day to work on delicate things like hairspring adjustments or pallet jewel replacement. But they are a whole lot more dangerous to work on.

I guess the WRT community will be polarized on opinion. :D

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I picked up a similar amount of these jewels some years ago in a watch and clock fair. Every now and then they come in handy. This week I've got a rubbed in bombe jewel in the balance cock that is cracked and needs replacing. Very handy to have a vintage assortment of these type of jewels!
    • Great diagram with the teeth and pinion count. Simple way to reduce the speed of the hour wheel by the 12:1 minute wheel. Genius and yet so simple. Always good to reinforce the principal by what you have done in your drawing. Keep doing that. I had a drawing on my wall for years showing me this which is very similar to the drawing you have done. Here's a formula to work out the beats per hour of a watch movement. The movement's BPH is dictated by the wheel teeth and pinion count and the hairspring being vibrated to the correct BPH by finding the pinning up point on the hairspring using a vibrating tool.  The reason in the formula there is X2 on the top line is because there are two pallet stones.
    • So I just wanted to say "thank you" again.  The angle is the key bit it seems and yes, it did basically just fall, or float, back into position when I got it lined up just right. I had meant to add that now that I see how it goes in, I totally see how it came out in the first place, and that whomever cloned the original movement didn't pay much attention to the fine details around the setting or how it interfaces with the balance cock or the "rings" on the regulator and/or stud carrier arms.
    • Well I’ve never seen the make before and cannot find any info, I haven’t got it just yet it’s been left to me among a 1970’s sea master and a mid size yeoman. But if anyone has any information on this one please feel free to enlighten me, many thanks 
×
×
  • Create New...