Jump to content

OMEGA660 Balance complete


Recommended Posts

Hello, I have just got the Omega 660 Balance complete(660-1327).
It seemed to be new and sealed in pack, but I doubt if its balance staff is broken.

I am quite new to this hobby, and this was the first time to purchase the balance complete.
So I am 100% not sure  if it is broken or not. 
I thought It should be like the 2nd photo.
Does anyone know about this?

Thanks in advance.

 

 









 

IMG_20200814_173356.jpg

IMG_20200814_173455.jpg

IMG_20200814_173601.jpg

Link to comment
Share on other sites

Hello and welcome to the forum.    I am afraid that balance is totaly u/s.  The staff has broken off where the roller sits.            Question        was it supplied in a sealed packet, was it an omega packet as to break the staff like that Its had takes a modicum of force.          life If purchased as new  return it to the seller for exchange or refund.

Link to comment
Share on other sites

Nucejoe
Thank you very much for your reply.

Watchweasol
Thank you for your reply.
I see, yes it was supplied in a sealed packet, should be the new one.
Also, thanks for the tech sheet.
I will request the seller to exchange or refund.

Thank you very much.


 

Link to comment
Share on other sites

If it was in a sealed factory pack, and it's not now, it would be a very kind seller to take it back. Add to that the fact that you weren't sure if half the staff was missing, as well as the roller jewel, from my view it's entirely possible the staff was "whole" before the pack was opened. Sorry if that sounds harsh.

  • Like 1
Link to comment
Share on other sites

nickelsilver

Thank you for your advice.
I noticed the roller jewel part was dropped in the bottom of the pack before I open it, from that perspective I guess the it was already broken when I opened it.
However I wasn't really sure what's going on, I opened the pack anyway.
I should have stopped opening it and should have taken the photo.

As you mentioned,  I think it would be a very kind seller too.
But I should give it a try anyway.
Again, thank you for your advice!

 

 

Link to comment
Share on other sites

Not totally worthless,  so if stuck with it, can be restaffed someday. 

Look at the bright side, who knows this may be a blessing in disguise, you might buy a staking set if it is just to restaff this one then go on to become a great horologist. 

Just trying to be cheerful. :geek:

Link to comment
Share on other sites

2 hours ago, Albat1192 said:

I should have stopped opening it and should have taken the photo.

Even though your package is opened I don't suppose you get a picture of the bits and pieces of the package for us?

Then a caution factory packages or basically the paper envelopes that typically watch parts come in except balance completes usually come in very special packages but any of the paper envelopes always require caution because it's standard operating practice for a lot watchmakers to put the old part back in the package.  Often times they didn't label that it's the used parts sometimes they do.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I picked up a similar amount of these jewels some years ago in a watch and clock fair. Every now and then they come in handy. This week I've got a rubbed in bombe jewel in the balance cock that is cracked and needs replacing. Very handy to have a vintage assortment of these type of jewels!
    • Great diagram with the teeth and pinion count. Simple way to reduce the speed of the hour wheel by the 12:1 minute wheel. Genius and yet so simple. Always good to reinforce the principal by what you have done in your drawing. Keep doing that. I had a drawing on my wall for years showing me this which is very similar to the drawing you have done. Here's a formula to work out the beats per hour of a watch movement. The movement's BPH is dictated by the wheel teeth and pinion count and the hairspring being vibrated to the correct BPH by finding the pinning up point on the hairspring using a vibrating tool.  The reason in the formula there is X2 on the top line is because there are two pallet stones.
    • So I just wanted to say "thank you" again.  The angle is the key bit it seems and yes, it did basically just fall, or float, back into position when I got it lined up just right. I had meant to add that now that I see how it goes in, I totally see how it came out in the first place, and that whomever cloned the original movement didn't pay much attention to the fine details around the setting or how it interfaces with the balance cock or the "rings" on the regulator and/or stud carrier arms.
    • Well I’ve never seen the make before and cannot find any info, I haven’t got it just yet it’s been left to me among a 1970’s sea master and a mid size yeoman. But if anyone has any information on this one please feel free to enlighten me, many thanks 
×
×
  • Create New...