Jump to content

mainspring replacement - first time advice needed


Recommended Posts

Hello All,

I am going to attempt a mainspring replacement for the first time and I will try to do this by hand as I do not own the set of winding tools.  I know it would be infinitely easier but they are not inexpensive and I am new to all of this.  Question is...the mainspring comes coiled in a disc typically.  Can it be transferred to the barrel without unwinding it and rewinding it into the barrel?  I apologize if this question seems lazy but I am trying to do this without too many chances to become unwound.

Link to comment
Share on other sites

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

4 minutes ago, MyRetroWatches said:

 no need to unwind. Just put over the barrel so it fits and use something flat to push it in.

This is how it's done and it has been mentioned here so many times (always good to search before asking), BUT...

If it's manual wind it's good to check first that the tongue engages the cut on the barrel. Before placing the lid turn the arbout with pin vices. Otherwise, depending on the mov.t you may find that it doesn't (it happened to me), and you will have to go back, remove and rewind to correct the problem. Truth is, having a winder is always a good idea.

Link to comment
Share on other sites

This is how it's done and it has been mentioned here so many times (always good to search before asking), BUT...
If it's manual wind it's good to check first that the tongue engages the cut on the barrel. Before placing the lid turn the arbout with pin vices. Otherwise, depending on the mov.t you may find that it doesn't (it happened to me), and you will have to go back, remove and rewind to correct the problem. Truth is, having a winder is always a good idea.

I did not ask the question. Was answering it.


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Just now, MyRetroWatches said:

I did not ask the question. Was answering it.

And I did not criticize your answer. Starting from it, have added an additional tip, if you allow me.

Link to comment
Share on other sites

Just now, MyRetroWatches said:

No problem. I am on Tapatalk so maybe it’s displaying wrong. Apologies

I recommend that you don't use it here. It causes many troubles and our Host Mark is about to remove support for it. The forum software is well engineered to allow full, unhindered support to all features from mobile devices.

 

 

  • Like 1
Link to comment
Share on other sites

20 minutes ago, MyRetroWatches said:

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

I've viewed this video ( I think its yours) and it is a big help in understanding how it can be done.  You had two old part barrels and you unwound and rewound by hand. Is that the one?  I have never seen anyone simply transfer the spring directly from the disc which seems logical.

Link to comment
Share on other sites

Apart from other issues, since the barrel is greased before MS is pushed in,  hand winding spring in becomes a greasy mess. Just push on the coil to insert it in, to avoid breaking the spindle,  it should be slid in along the line of cut on barrel wall.

  • Thanks 1
Link to comment
Share on other sites

I've viewed this video ( I think its yours) and it is a big help in understanding how it can be done.  You had two old part barrels and you unwound and rewound by hand. Is that the one?  I have never seen anyone simply transfer the spring directly from the disc which seems logical.

Hi Duke,

 

You're correct in that you can simply transfer the mainspring from the ring into the barrel. Just make sure it's seated correctly and is orientated the correct way. I understand why you asked the question as it is a little daunting the first time you do it but if done slowly with a flat implement there's very little that can go wrong.

 

Some people probably do it different but I've always used the other end of a pair of tweezers as they're solid and flat.

 

Good luck! By the way I haven't sprung for a set of mainspring winders yet and have always opted to simply purchase a new mainspring and insert it using the above method.

 

To help illustrate what to check for before putting it home I added a very crude image below. Just make sure it's all the way in up to the disk all around.

 

 

a29e6af399a137c3d7cd6f5846f9813b.jpg

 

 

Sent from my SM-T510 using Tapatalk

 

 

 

  • Thanks 1
Link to comment
Share on other sites

8 hours ago, MyRetroWatches said:

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

I learned how to do this from your video, thanks for that it was great.

The bit about the pin vise is great, and having one really helped me in the learning process, being able to test whether the arbor was properly hooked up to the mainspring.

 

I got a Starett pin vise for .8-1.6mm diameter, which is perfect for this purpose.

Edited by pubudeux
  • Thanks 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This is a very sad day for the industry.. For most of us being amateurs the cost of replacing parts for ETA,s etc will be beyond affordability for the customers.   see full statement below   We have now received the decision from Judge Michael Green on whether or not the High Court has jurisdiction to hear our claim against Swatch, and sadly it is not the decision we had hoped for.   As we have pointed out in previous news items (see below),the rules that Judge Green had to apply strictly prevented him from examining in any way how the Swiss Court arrived at its verdict, even if it is blatantly obvious that the verdict is wrong.   As Swatch’s lawyer was summing up in the last few minutes oft he hearing, the Judge twice pinned him asking if it was alright if, as a result of the Swiss verdict, consumers had to pay 50% more for their watch repairs. After some stumbling, their lawyer’s reply was “Yes”, so  I am quite sure that Judge Green left his court fully aware that the Swiss verdict does not reflect the norms of British Competition Law. However, the rules simply do not allow him to take that simple fact into account.   Judge Green noted that our two arguments relating firstly to British Competition Law now being different from that of the EU, and secondly to the contention that the legality of the Authorised Service Networks has not been tested, had both been mentioned in the Swiss verdict. Because they had been mentioned, he felt that to allow us to argue them again would constitute re examining the Swiss case, and could not be allowed.   As to our claim that we were denied our right to be heard because our evidence was not considered, our lawyers had argued that the evidence we provided could not have been looked at because had the Swiss Court done so, it could not have reached the conclusion that it did. In his verdict, Judge Green highlighted general statements in the Swiss verdict that evidence had been looked at, and acknowledged the arguments we made to him, but again he considered that this was re-examining the Swiss verdict, and could not be permitted.   Our case has attracted considerable interest within the Legal community, and within minutes of the decision being made public we were approached for comment by one of the largest subscription news services, Global Competition Review. They asked us two very pertinent questions, and I reproduce them for you below along with our responses, as they neatly summarise the consequences arising from our case.   What are the key takeaways?   Enormous damage has been done to the fundamentals of UK and European Competition Law by the Swiss courts. It has always been the case that the effect on consumers and competition has to be considered in any decision making, but we now have a ruling that states even monopolists can remove wholesale markets from the supply chain without any consumer benefit based justification. Those entities looking to subvert Competition Law and exploit consumers for their own benefit will be looking at this very carefully.   Has the court made the wrong decision? If so, will you appeal?   The issue lies not with the High Court, but rather with cross border jurisdiction treaties that have no requirement in them for foreign jurisdictions applying UK law to take account of the Ratio Legis [a legal term for the fundamental reasoning why the law was written] of that law, and have no remedy within them for UK Courts to overcome decisions that clearly do not.    After eight years of work, and a very considerable sum in legal costs, I can not begin to tell you how disappointed I am at this outcome. For the time being, there is no further route through the British Courts that Cousins can follow. However, I promised that we would fight to the end, and that promise stands.   The UK is no longer part of the Lugano Convention, whose rules Judge Green has applied, and as yet nothing permanent has replaced it. The political tide turned against repair prevention by restricting supply of spare parts some time ago, and our efforts on behalf of the Watch Repair industry have resulted in high level contacts within several Government Departments. You can be sure that we will keep working to overcome this unjust situation that we now all find ourselves in.    I will keep you advised.   Kind regards   Anthony
    • Dell fancy a challenge🤣   https://www.ebay.co.uk/itm/285785684626?itmmeta=01HT29WVJY21Q94C73GYHGBTFX&hash=item428a277a92:g:15YAAOSwNRVmBAUz&itmprp=enc%3AAQAJAAAA0DIe4QLQBW66rSyIMiyBuk8GY%2B86pQ%2BQnxGbcNq7egAGe5DIs9YMmiWJIbZtMSxwNJIiJxuojbq523IeUSBQ6pJEIQ0tfz2ChrBR03BksmKINyklg1IK4GAfAcYY9Hta9wVeSZSZN7ZCNAfZTgKs9c4%2BUIUZ3Qjc3QjUXDn2uPRo1FiYOEewMG5A26EXb%2BclBgrqtbOmM6P3bea%2F8ZImOAXNI1HtbmtMk84pIGoM6ISwaM1PKFuADtTFMccS5e3ZjndCbXYXHrW3CecsV0edw3M%3D|tkp%3ABk9SR8q588nQYw Darwin’s theory of evolution has not been proven to be absolutely.  😀 
    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
×
×
  • Create New...