Jump to content

Glass replacement guides


Recommended Posts

It seems that selecting the correct glass is a dark art, one I have no experience with.  I've searched the forum and read 15 or so posts about it.  I've read the Sternkreuz PDFs.  I've watched Marks videos on it...

I'm still clueless as to which glass I need for a watch.  Before I post pictures and bore you all with yet another glass replacement question, does anyone have any other links to guides on the subject?

Link to comment
Share on other sites

I simply identify the required crystal diameter or dimensions using a digital caliper and then find the most appropriate crystal in the G-S supply catalog available online.  This is the easiest part of watch repair for me, hope you have luck too.

Link to comment
Share on other sites

I recently discovered it's not always that easy though. I have a watch I'm working on that has possibly 3 critical dimensions. The OD of the crystal, the ID of the crystal, and the height of the straight section of the ID. The case uses the crystal sandwiched between the front and back of the case as a waterproofing feature (though it completely falls apart at the stem best I can tell), and the case won't even stay together without it. I carefully measured, then called GS and they carefully measured, but still the crystal I got is ever so slightly the wrong size in all dimensions.

Link to comment
Share on other sites

It's normal to have to slightly grind glass crystals to have them fit well. That is much easier with plastic ones. This is where the repairer/watchmaker ability comes, not just picking parts from websites or catalogs.

Link to comment
Share on other sites

I think my problem is that I'm coming at it as a complete novice.  For example...  I get that high dome is higher than low dome, but I'm looking at the old glass and don't know which it is, I have no reference point. 

For acrylic glass my chooses are...

  1. N, Ordinarily domed
  2. HW, Highly-domed, extra strong
  3. HWS, Highly-domed, with step
  4. HH, Extremely highly domed
  5. M, Slightly domed
  6. NB, Ordinarily domed (Again?)
  7. HB, Highly domed

I suppose the best way would be for me to buy one of each and compare them myself.

Then looking at my case, there is a metal ring, not a tension ring, it has markers on it (reflector ring?) and a plastic gasket(?) but I don't think the glass fit into it, rather sat on top of it.  It's all very confusing.

I guess I've not seen enough watches to work out what I need.  So I'm looking for a document or handy guide to the basics of glass replacement and if I can't find my answers there then I'll have you ask you kind lot of friendly people.

Perhaps I should start a document myself to help the next person that comes along...

Link to comment
Share on other sites

On 7/15/2020 at 9:09 AM, jdm said:

It's normal to have to slightly grind glass crystals to have them fit well. That is much easier with plastic ones. This is where the repairer/watchmaker ability comes, not just picking parts from websites or catalogs

one of the problems with the mystery of crystal fitting at least at the professional level is typically professional watchmaker's if they live the right part of the world do not fit crystals themselves. In the bigger cities at one time the material houses located near to the watch shops were if you needed a crystal you would just physically go the material house hand them a tray of cases come back later you'd have crystal fitted. Why should a professional watchmaker waste their time if there is somebody else could do it for you?

but not everyone has access to a material house that means you're going to have to fit the crystal yourself as soon as you figure out what it is. I've attached the handout they help figure out what it might be

 

 

GS Crystals.PDF

  • Thanks 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • It's pronounced "bombay" like the city.  French for bomb is, 😄, bombe, pronounced the same as in English. Bombé, bombe.
    • That's a really good idea! I have a 3d printer, I think I'll design something that I can clip on to the edge of my desk to do the same. Thanks for the idea. 
    • I looked up bombè, domed in French.  It's pronunciation is bomb, does a bomb (explosive device) get It's name from bombè? I know we're going off subject but it's interesting. 
    • Okay, I checked with the fine folks at the McCaw Company, and they agree it's the correct crystal, and they have one in stock, so with that sorted time to get onto assembly. Starting by getting the spring into the barrel, which was a bit harrowing. It took me several tries to get it hooked onto my worn old winder arbor, but I did find a new use for the micrometer stand I just purchased. Carefully dabbed some Kluber P125 braking grease to the left of the divots around the barrel, and a little HP1300 on the floor of the barrel before popping it in--in case you haven't seen it, this is a great illustration I found somewhere on this site. You're not the boss of me, Bulova.   2172_Bulova 11AOAC 11AOACD 11AOACB.pdf Bulova_11 AOAC, D, B(1).pdf I got the train back in and it didn't seem as free as I'd like. Looks like the driving wheel with cannon pinion has zero end shake. That could explain the low amplitutde I started with. Now if you were me, would you push on the plate jewel or the bridge jewel? I've attached some extra pictures in case anyone sees something else I'm doing wrong here.
    • I have quite a few watch brands from all over the world. For some reason this Timex electric from 1979 is capturing my attention this week. I am not a particularly fond of battery operated watches or Timex, but this one is different for some reason. Post your watch in your collection that seems to draw you in more now than before...
×
×
  • Create New...