Jump to content
WD041

Newly Joined Introduction

Recommended Posts

Hi all, I Repair and service mostly vintage wrist and pocket watches busy repairing a generic watch containing a French Ebauche FE 3611 movement. The missing stem according to Ranfft is a W3246. I can't see it in my Flume book or dimensions on winding stems.com . Idealy it would be easiest to convert to a bestfit number then I could look up interchangability or find something dimensionaly close that I could modify. Are there any charts out there to change from ronda, bestfit and W stem standards.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Hi Certina was founded about 1888 by Adolf and Alfred Kurth, The K is for Kurth placed on crowns of early Certina watches. Hope this helps 
    • That video above shows Rolex hands which are made of solid white gold and responds well to polishing. Most hands on the other hand (pun not intended) are plated brass which do not as the plating can easily be worn through. Use of rotary tool not recommended. 
    • Looks good. Did you try “topping” the repaired wheel, ie. checking if the new teeth are relatively proud of the original teeth and stoning down? Must have been a really tricky job at that size!
    • Well I think I've successfully done it. Thanks for all your words of advice. My method was to first assemble the train wheels and bridge and check they were freely spinning - all good. Then I tried the barrel held by its bridge without adjusting the tooth and as expected, the spin came to a hard stop and lightly bounced back. The gap of the good teeth is around 0.4. My 0.5 screwdriver blade got over half way between the gap of the bad tooth so using this I did a straight firm push (no back and forth levering as I hoped the wedge of the blade would push apart). On pushing the 0.5 home, I moved onto the 0.6 and repeated. Then onto the 0.8 (sweating by now as it seemed to take more pressure to drive home). At this point, I tried it against the train, and again, the same happened with the bounce back. Feeling my luck was going to run out soon, I applied a tiny drop of HP 1300 oil on both sides of the 1.00 screwdriver blade in the vain hope it may ease the blade in, and it did seem to ease the push home. On examining, I recalled @AlexeiJ1's advice that it doesn't have to be perfectly straight, just more inline, and it did appear improved so trying with the train again, it spun freely with no resistance past the imperfect teeth. Of course I won't know if the performance will be affected until she's up and running but for now, I'm pleased with the result. I've attached a photo of the straightened tooth.
    • One trick I learnt is to use balsa wood. Get a block of balsa and press the hand into the end grain of the wood until it is practically inlaid into the wood. I usually polish the hands by hand with Autosol using a piece of pegwood for rubbing. Knowing what the material the hands are made of is really important. Brass is very soft. Using too much pressure will bend it. Steels are brittle and can break, especially those hollowed ones for holding luminous paint. When using rotary tools to polish, use very low speeds and light pressure. I don't like dremel tools. I prefer to use a dental lab micromotor which has better torque, speed control and less vibration.  Don't use tools that can catch the edge of the hands, like a cotton mop or felt. Use silicone polishers. I just can't work with conventional lume paste. The solvents evaporate so quickly that it's hard to get a smooth layer. I prefer using a UV cured paste. I use UV nail varnish and add lume powder to a consistency I like. Use a large oiler to spread the paste in 1 smooth stroke, using very light pressure almost not touching the hand with the oiler. Excess paste can be removed with the oiler. Then cure it in a UV nail dryer for 2 minutes.
×
×
  • Create New...