Jump to content

404 Club


Recommended Posts

From ebay auction to cleaned, serviced and on the wrist in just over a week.

The latest 404 club offering. As expected it has a Soviet era  Raketa 2609.HA, and as is often the case, it arrived filthy and the crown wouldn't turn the hands.

RIMG0963.thumb.JPG.20d7d5770076a5e571d97cd68bb0f9b7.JPG

It actually arrived a couple of days ago, but I hadn't had a chance to look at it.

Since it was raining today, I had a day off from trying to keep the garden under control, and  gave it a full clean both inside and out, and some home brew tractor oil and vodka mix and off it went.

OK that's a slight exaggeration, but I did decide to treat it to the witches brew neatsfoot and baby oil, rather than the good stuff,  so it also joins that unfortunate bunch, all of which are still alive, despite my dastardly experimentation.

It is now sporting a new old stock 18mm black leather Apollo band. 

The leather on this batch of Apollo straps was a little dried out when I grabbed them as a job lot of four (also for <£4.04)
Neatsfoot oil on its own was used to wake up the leather and it now actually feels really soft.

I wont bore you with my limited set of servicing pictures. Instead, I'll point you to Marc's full strip down and rebuild of an identical piece here. ->

Thanks for those, they have proved very useful with several of these 2609.HA pieces.

I rather like the look of these, in fact I have another one on its way, also picked up for a pocket money price of course. 

  • Like 3
  • Thanks 1
Link to comment
Share on other sites

On 6/20/2021 at 12:56 AM, LittleWatchShop said:

Gots to me one of dem Russian watches!!  I was watching one a day or so ago and let it slip by.  Ebay is forever...so I will get one.

Well worth picking one up.

The most common issues are keyless work problems as described in Marc's servicing post. One or two I've looked at were so badly gummed up with junk and corrosion that it needed great care to free them up without breaking anything.

That and obviously the usual gummed up old oil and attempts by people with fat fingers to fix things, resulting in screwed up hairsprings.

Also watch out for the shims under the balance bridge. Sometimes there are none, sometimes one, and occasionally even two of them. They are easily overlooked when disassembling as they tend to stick to the back of the balance bridge or the main plate unobserved, only to then fall out later and get lost.

I think these USSR era watches are quite under rated and often overlooked, but with a little TLC they spruce up very nicely and if correctly serviced they run very well too. They are also pretty easy to service as there are not many parts, and no "gotcha" springs or weirdly constructed complications to deal with.

Edited by AndyHull
Link to comment
Share on other sites

13 hours ago, LittleWatchShop said:

A little uninspiring.  It does run though...kinda.

2021-06-21 20_44_38-Photos.png

The EB 8800 is the first movement I serviced. It’s also the first one that I broke (balance staff). 🙂

I like them ok. Easy (quick) to service and solid runners. I have at least 10 of them (half in Chateau/Lucerne jump hours).

  • Like 1
Link to comment
Share on other sites

10 hours ago, LittleWatchShop said:

@AndyHullwhat do you think about Vostok Russian watches? 

Well they can be a little bit "agricultural" in their construction, but they are generally very robust.

RIMG0027.thumb.JPG.08d11850b39d57f143cddc8a3d3b4ce4.JPG


I have this rather natty blue dialled Bostok Командирские (Komandirskie) that I'm particularly fond of, which I paid a bit more for than the 404 club rules allow (although not that much more), and a couple of other  that are 404 club members.

There are some interesting examples here too -> https://mroatman.wixsite.com/watches-of-the-ussr/komandirskie

They are by no means luxury watches, but they fun, quirky, a little bit different,  and fairly well built, and certainly if the price is right, then get yourself one.

Link to comment
Share on other sites

I couldn't resist this, despite the terrible picture.

AsPurchasedCropped.jpg.9c6549bc594a723b30cf913d8e78a7e1.jpg

Yes I know. Madness. I just posted one of these a few days back, but it was three quid, (well three pounds and forty pence to be exact, no other bidders) and the other pictures in the auction showed that the second hand had moved, so it probably isn't a complete basket case.

Now I have three of them, one of which I am currently wearing (which is putting in a good solid +/- 10 sec/day performance).

Its fine. I'll just need to grow another arm, that's all.

Edited by AndyHull
  • Haha 2
Link to comment
Share on other sites

The latest candidate, a Rotary Quartz for a pound. 

AsPurchasedCropped.thumb.jpg.be415757b2f5a82a45ebbbacd5509e38.jpg

 

Judging purely by the styling I would think it is late 1970s or early 1980s, but I could be entirely incorrect. If i is late seventies or early eighties then it might have an interesting jewelled quartz mechanism in it.


I'm hoping that the only issue is with the crystal, but given the price, even a complete basket case would not be a major disaster.

  • Like 1
Link to comment
Share on other sites

Some of the 404 club USSR Sekondas.

RIMG0029.thumb.JPG.9b122a11023bc4e2d9032280b15f3cfe.JPG

I have a few more, including a number of USSR era mechanical watches, and some duplicates of the ones above.
I also have some Poljot, Raketa, Luch and Bostok USSR watches from the same era.

Edited by AndyHull
  • Like 2
Link to comment
Share on other sites

I assume it is symmetric cushion. What are the dimensions?

I have an ambition to become the "crystal man" so I bought this one:

 IMG_20210628_123847.thumb.jpg.e293eb8d56f7dd15167899df9956e909.jpg

IMG_20210628_123835.thumb.jpg.c0e9b83d928ec54783b69f28c53d937e.jpg

IMG_20210628_123812.thumb.jpg.1813a0ed7b3f0e9786f4712d55a88956.jpg

IMG_20210628_123745.thumb.jpg.b44711106b0eef36dcc056a747c01b1c.jpg

I have not tried it yet though. The drawback is that you have to have the original one to copy it.

"The glass and plastic lenses of today are termed "crystals" because of this seventeenth century influence."

IMG_20210628_124541.thumb.jpg.699d906463edd9f3cb22474a8317324d.jpg

 

Link to comment
Share on other sites

I'm attempting to divine how that machine works based on other machines I've worked with in the past...

Top flips up/down. The collet on the left somehow holds blanks, and the stylus on the right traces the original? Or, no... The motor turns the shaft on the right, so it'd have to be the other way around... The bases slowly turn in unison with the handle on the right, the cutter is on the right, the original and a stylus (not pictured) on the left. As the plattens turn, the top plate slides left and right to trace the shape of the original as the cutter cuts the new blank. I think that's it. That's what I'm going with.

Link to comment
Share on other sites

On 6/22/2021 at 10:43 AM, PinLeverPete said:

I like them ok. Easy (quick) to service and solid runners

I serviced this one today.  I did not realize how the mainspring was configured...!!!!!!  Jack in the Box.  Ugh

Nothing broke, but getting the mainspring reassembled was...uh...interesting.

It is running fine now.

  • Haha 1
Link to comment
Share on other sites

A couple of Kander 25 jewel Baumgartner 1582 automatics for for £1.60 each plus P+P

AsPurchasedCropped.jpg.92c36c3b666efafd8a8ff82e9a979b5c.jpg

They currently look fairly terrible, and one is missing some parts of the automatic mechanism, however I am pretty certain I have a donor movement in the junk pile, so hopefully I can get them both working.

I posted about a Kander watch a while back, details below.

 

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

1 minute ago, LittleWatchShop said:

I am filtering for US sellers only...I think you guys are seeing much better deals over there.

I need to filter out US sellers here, as the postage to the UK is generally eye watering.


Recent Brexit related changes mean that EU sellers items now incur additional tax at point of sale, which tends to push them out of the 404 bracket.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • No, the Peseux 7040 is doing very well as far as the rate (and amplitude) is concerned. The maximum delta measured was 20 seconds between fully wound, crown down (+8 s/d) and fully wound minus 24 hours, crown up (-12 s/d). Compare that to the ETA 2763 having a delta of over 80 seconds. What I was trying to convey was that I observed that the much higher amplitude of the Peseux movement during a 12-minute measuring period could momentarily fluctuate by 30° just like the much lower amplitude on the ETA 2763. I haven't studied the History graph on @praezis PCTM software for any other than these two movements but I wouldn't be surprised to learn that these fluctuations in amplitude during a 12-minute measuring period are the rule rather than the exception for all typical non-high-end-chronometer movements.
    • I'm presently using a cheap supermarket ultrasonic cleaner, with L&R #111 cleaner and #3 rinse solutions. I cut a bit off the bottom of an appropriate size plastic sports drink bottle, which is a perfect fit around the mesh basket I use (~65mm diameter). That allows me to use mostly water in the machine tub and cleaner or rinse only in the small plastic container. I keep the solutions that are still fit for use in small glass jam jars. I use the cleaner then two rinses, then the mesh basket balances on my bathroom radiator (once it stops dripping) to dry the parts with moderate warmth. Prior to that I tried just lighter fluid (eg. generic zippo fluid) and just soaking / swirling parts in the glass jars, but the movements did not run at all well afterwards, they were still acting gummed up. The proper solutions make a world of difference & the watches now work as they should!    
    • Have to agree with you. Will not do another. Did not enjoy the time spent. However, it was worth it to know that I understood how to disassemble, look for defects, repair and then assemble. Timegrapher? No facility to alter anything other than the stud. Everything is metal to metal.
    • Couple of things H. There surely seems to be a reoccurring fluctuation pattern  of somewhere around every 5 minutes. More noticable with your crown left trace having a large peak gradually reducing to 2 small peaks and troughs then back up to another large peak. Nev posted a download link to a book by Harold Kelly not so long back that i started to read while i was away. There was a good section on wheel and pinion ratios, rotation periods of wheels of different beat frequencies that's worth a read. Then something that bugs me comparing the amplitude and timing rate changes with your dial up trace which i chose to avoid wheel imbalances . The amplitude fluctuates by an extreme of 30 ° and the rate fluctuates by an extreme of 21 seconds as per your reading. In normal circumstances a movement dropping its power over the course of the mainspring unwinding, a hairspring acting isochronical will maintain its rate almost to the end of the power reserve. Similarly power wound into a movement increasing its amplitude from 265° to 295° a hairspring again acting isochronical will again maintain its rate aside from a brief few moments until it settles into it's rate. From that it seems to me that because the amplitude difference isn't big enough to affect a rate change then the amplitude fluctuation cause is not coming from anywhere but from the balance. So its whatever is causing the rate to change increase and decrease within the balance is also slowing and speeding up the hairspring swings. I'm not quite sure if I've just gone around in circles with that, it made sense to me when i started  😅 We did have a discussion a while back when i asked if rate could come from that point as well as from the regulator pins. This area can be electro stiffened in high grade hs i remember was the answer. I remember that over Ross's issue with balance endshake.
    • somewhere in the universe although as I'm answering this I remembered which discussion group. Somebody had a similar question loss basically expanded it to the watch would totally disintegrate in my think like 30 years. I'd have to go back and find the original discussion if I can the person seem to think that they hairspring would disintegrate like you describe and just metal on metal wearing out the entire watch. Except of course we all work on watches over 30 years and they obviously do not disintegrate. Plus somebody came along and explained why hairsprings do not have the same issues as mainsprings. Although hairsprings do end up with watchmakers insisting on bending and playing with them and torturing them etc. and that obviously is not good for the metal at all. one of the problems that you're having here it is what is the purpose of the test that started this discussion? Let me go and snip out the original image as you can see from images above this watch is horrible. Or is it? What is the purpose of the images up above in other words what exactly would use this test for? The real purpose this test is show the effect of amplitude on timekeeping. Or specifically you're looking for mechanical issues that are causing fluctuations in amplitude which unfortunately shows up  with timekeeping. or basically everything affects timekeeping but amplitude is affected by the mechanical characteristics of the watch from the mainspring to the balance wheel and unfortunately as it's a mechanical watch your always going to have power fluctuations. so how do we rule out unacceptable fluctuations versus the natural characteristic of the watch? Usually if you can find a repeating pattern you can narrow it down to the offending components for instance I'm attaching a PDF. on the second page of the PDF it talks about 21st-century equipment versus paper tape timing machines. Then they give an example of timing problems solely caused by a faulty component. although off you have a user's manual for a paper tape machine it does explain that you can find faulty components by looking at the variations on your paper tape seeing how often they repeat and do the same thing without the fancy software. Even though it was claimed that you couldn't do that in other words you couldn't find a pattern? One of the problems that comes up with modern LCD-based timing machines versus software is limited screen size. In other words it makes it very hard to look for patterns you'll see variations in numbers but it's hard to tell what's going on which is why the display above is really nice to see if there is a problem. for instance here's a paper printout from a witschi timing machine it does look distorted because I changed the speed at which the image would move across the screen. In other words I was trying to figure out a way to extend the screen to being much longer as I was looking for a pattern as you can see there doesn't appear to be a pattern at all so basically we end up with a watch that I cannot time at all they cannot really figure out what the problem is and I actually cannot find a pattern even begin the figure out where the problem might be. Plus I agreed to service this watch for free as I was going to use it for the purposes of a lecture. In other words it's a nice railroad grade pocket watch and I wanted to show before how horrible amplitude is and how wonderful it looks after serviced and after servicing it looked exactly the same still horrible. Then I used software for a clock timing machine and came up with this interesting image one a minor problems we have with time plots and  how they look is that they all do things a little bit differently. So this was occurring approximately every five minutes. Then we need another chart then I replaced something in the watch and we now get this one of the things that I was always bothered with was if I had put the hands on after servicing would the watch have Time? Because the pattern was repeating the watch would average that out may  it would have Time. Oh and what did I change somebody had swapped the mainspring barrel for something different were getting a binding between the mainspring in the center wheel pinion. so the problem you're having is what exactly is the problem? the purpose of the test image is to look for mechanical problems causing amplitude problems. Because it's a mechanical watch your always going to have variations so are the variations in this watch abnormal or normal for this watch? Once we eliminate the mechanical issues beyond it's a mechanical watch then you can work on timing issues. for timing issues I recommend going back to the normal display that were used to and make sure you have your averaging times set correctly. In other words while the graphical display is basically real time years of the numbers are averaged over time. Anywhere from 20 to 40 seconds depending upon whose specs you're looking at. So basically they will average out the problems were seeing on this time plot.   one of my amusements with students that go to the same school is that you have different instructors. So this gives you different experiences like what exactly is tight anyway as I don't remember any thing like this? Then did you know that Rolex at least in Geneva as I visited their service center replace all the screws in the watch every time they service the watch. then why did they do that because they use power screwdrivers and tighten those things down as tight as you can get them which has a problem. How many times can you tighten screw down really tight before the hints break off. So they replace the screws every single time. So personally I don't think they have to be so tight that you're in danger snapping head off that's too tight in my opinion. but the screws definitely shouldn't be falling out either which I've occasionally see and where people just don't tighten their screws tight enough.   Horologica Times -- May 2004 From the Workshop witschi time plot.pdf
×
×
  • Create New...