Jump to content

Hello from Monterey, CA.

JeffInMonterey
 Share

Recommended Posts

JeffInMonterey New Member

JeffInMonterey

Posted
Posted

I have been repairing mostly clocks and some watches for several years.  I have a several clocks and watches of my own that I need to repair and it seems like I never get time to do them.  I am always (so it seems) working on items belonging to other people.   With that in mind, I am thinking of retiring.  With the shutdown, it has been easier to work on several of my own things. I have also become involved in woodworking and have built a couple of clock cases using old movements.  I get a lot of satisfaction in this, but my woodworking skills are limited.

I have been a member of NAWCC since 1972.

IMG_1437.JPG

IMG_1440.JPG

20170321_140551.jpg

  • Like 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
25 minutes ago, JeffInMonterey said:

Thank you.  Hope your country comes out ok with this virus.  I have been hearing the news about how bad it is there.

Thank you, fatality rate dropped considerably in the wake of lockdown and its picking up speed again, new preventive measures were put into effect as of yesterday.

A bit of good news anounced on TV last night, researchers in Tehran have had success producing Vaccine, said to start testing it on human and expectedly be ready to present to WHO in three months. 

And that we expect better news from research institutes out of four other countries before long.   AmGen said to have made substantial progress, Expected of the Giant.

 

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Thank you for your introduction and welcome to this friendly forum.

Two very nice visible escapement clocks. The first is French and I expect its an 8 day duration with rack striking on a bell. Is the other French? it looks like it, both very nice.  

Link to comment
Share on other sites
JeffInMonterey New Member

JeffInMonterey

Posted
  • Author
Posted (edited)

Thank you.  The table regulator is based on a French design I saw a picture of somewhere.  the original clock probably dates from about 1860 and is made of black slate.  I like the simplicity of the case and having the large dial (7") and the pendulum stand out.  The woodworking was not too difficult.  However, the curved glasses on the top were very difficult to get made.  The guy had many failures in getting the curve done correctly.  The wall clock has a huge 9 inch dial.  The movement has rectangular plates, not round.  I bought the movement with the dial and I never saw a French clock like this with such a large dial.  The glass is about 3/8" thick and the bezel is very heavy.  The movement must have been in a very large slate case of some kind. The pendulum for this clock is from another clock and I modified it to fit this set up.  Both are rack and snail type striking.  The wall clock has very large springs and it runs about 10 days.

Edited by JeffInMonterey
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...