Jump to content

"Louis XIV" alarm pocket watch.


Recommended Posts

imageproxy.php?img=&key=8c41f123521b3122Not rare, nor exceptionally valuable, but of my several pocketwatches, it's one of the most useful and endearing.  The third hand sets the alarm. At work I might go to lunch at different times, there is no clock in the breakroom, and dealing with protected information we must lock up our cell phones before duty. Watches are how we tell time there. My alarm tells me when my break is over.

Technically assembled by Public Watch Co, with a Baumgartner 222 movement, it is surprisingly accurate for what it is (that, and I spent quite some time regulating it). I think it's around 50 mm +/-.  Value-wise, it's probably a step up from "Dollar watches", but I love it anyway; it's alarm has been a handy reminder quite often.

20200430_194841.jpg

20200430_195224.jpg

20200430_195315.jpg

  • Thanks 1
Link to comment
Share on other sites

I'd have to check, but I think it's a video that I've seen.  There are a few of these handy little watches out there.  Maybe I could post my own video here.  I'll have to film it in action!  That'd be a cool thing.

Edited by KarlvonKoln
Typo
Link to comment
Share on other sites

So here is the requested video.  Isn't the alarm feature just the handiest doggone thing?   Sure, I could set an alarm in my smart phone, if it was required to lock it up, and if I didn't have to open the app, pull up the date, set the hour, then the minutes, then am or pm, then select a tone, then hit save (then look at the time on the screen and realize I now have to clock back in anyway).  Perhaps I exaggerate, and perhaps not, but this certainly seems way easier, even one-handed. 

I had to trim the video down a bit, but it still seems to show enough about how simple it is to work it.

Edited by KarlvonKoln
Weirdness ensued.
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • It might help us if we knew which watch like model number.
    • Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...