Jump to content

Case for Seiko NH25A Movement

nlapietr
 Share

Recommended Posts

nlapietr Watch Enthusiast

nlapietr

Posted
Posted

Hello all,

I watched a video on assembling your own watch from parts on ebay and got so excited I promptly ordered parts that don't work together.  I purchased a Seiko NH 35A movement and a 28.5 mm dial and hands.  These all work great together.  However the case I bought was WAY to big.  I have been searching all day for a case the correct size but cannot find anything.  Any suggestions on sources or other ideas?

Thanks in advance for any advice.  I love the videos and discussions.

Nick

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

I think the nicest cases you can get are from Seiko 5 watches. Any cheap 700x or 7s26 one will do. Stainless Steel, so can be repaired and polishing perfectly.

Otherwise you will have to spend a lot of time and effort adapting.

Link to comment
Share on other sites
nlapietr Watch Enthusiast

nlapietr

Posted
  • Author
Posted

Ok, so here is the next dumb question.  Would a chapter ring fix the problem and how do you know how to size (probably going down from about 38MM to 28.5?  Are there standard size charts somewhere?

 

Thanks again.

 

Nick

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
11 hours ago, nlapietr said:

Would a chapter ring fix the problem and how do you know how to size (probably going down from about 38MM to 28.5?

No. The chapter ring is the one that may sit on top of the dial, with minutes or other markings. Perhaps you are referring to a spacer, or movement ring. Your NH35 comes already with one of grey plastic one. If it's size is not adequate, a watch manufacturer would replace it with a different one.

11 hours ago, nlapietr said:

 Are there standard size charts somewhere?

There are no standards. Movement size can be expressed in old French lines but that is just indicative, then each movement has a technical drawing for casing that show all the size including the very important hand and stem height.

If you are OK with bodging up an holder ring, there are assortments that you can buy, or use whatever common material at home. Otherwise making it perfect requires 3D printing, or precise metal turning and milling, even if hand made.

Link to comment
Share on other sites
AshF WRT Addict

AshF

Posted
Posted

If you have a 3d printer then it's possible to make a movement holder to position the movement correctly inside the case.  I've done this for a custom watch I made.  I also printed a dial is it was a skeletonised movement.  It takes some time and effort to get right, here's my prototypes...JyCoBLI3OZ4ILpEfte4GB37r7aZfsQz5d2nJZ0qPkSP1pw8BZH3ZvqmpszDxHQpJd1yrbr8mz-E1FQD7slljks30nYDV7SOfuHMXgHzIQFB99f07bLNjGF_rQ-oqO6ZK6OYptz-C6dqSCBCf_rjTn_eD0fPqOg9skqYZFmg3azsxJjxOsoP79vN7Q6gviTOdfIDYTPJZiQr61yqZPyYP_YAdaapJBzo5W66cWOYlDA-rPFewHKhZOAl90ebEIibf53Or83O4S-lsCUifFuoe5fp91aQ1HPHX85R6P2M5z7nzZuZc7Z8b2qv0Y6DkLN8iw5EIfpM8Ti8GcD48e7goxrD-bx94UF7_9lsLLvfKdgWROmpFLkCdhQgu4WkodZVBlm-DER0Pnd-EUb75q1b79v6tWVX0rGVnJNeCXkU1t_djrwCfNEJ63B95vhkfDC8Fc-LvlNTHUTL1WgYl_Ro89ACMUNpQjXnLIhWFNveUOHAC0wqKkBkCRX-IBjQujohtecLbL3UVXCuPwKBObHyifB1H3VpzWQJv62jIvbf2gNcREs38-FeGJRNkl7egi5GWFpIKFYdnrQKD807PcTpyVBJFVlwB9cOdJsApEHWHwXOVMZNDOsAmcIGxTRMK6wte_zUq5wCiImxgPCCGdP5giQlDKG2H7xn--hDEf6eOuA0V5-vbMmrHQWCk=w847-h1129-no?authuser=0

  • Like 2
Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted

If you are not opposed  to used parts try speedtimerkollektion. You can buy used cases in lots. 28.5 mm dial diameter  is pretty  much a seiko standard  size. Pay attention  to stem location. It varies 

  • Like 1
Link to comment
Share on other sites
  • 2 weeks later...
WatchCodger New Member

WatchCodger

Posted
Posted

There are now many suppliers of aftermarket cases for Seiko 72XX and NHXX movements. Have you looked up CrystalTimes? Theirs are  SKX-type (diver) cases that accept the parts you have (in addition to others required). Namokimods just announced "Rolex Explorer" style cases (two vintage sizes) that accept the parts you have. The later are currently pre-order. There are others as well.

My apologies if you've figured this out already!

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, WatchCodger said:

Theirs are  SKX-type (diver) cases that accept the parts you have (in addition to others required).

Seiko diver's knock-off cases starting $99?

Fat springbars $22?

Ahaha! I'll rather buy the genuine article, or if it is about made in China, at their real prices.

Link to comment
Share on other sites
WatchCodger New Member

WatchCodger

Posted
Posted

Is there such thing as a JDM SKX case, specifically? Is the case from an SKX007J made in Japan? You can't get an SKX OEM case, seperately, now anyway. My personal "knock-off" SKX cases are at least as nice as my OEM ones, if not better (drilled lugs). $79 should about do it for an aftermarket SKX007 case, which sounds pretty good given the current $250+ full price for an OEM SKX007J from a reputable online seller (way up since being replaced by the new "5"). Sure, grey market is cheaper.

Fat spring bars should be about $6/pair from any seller. $22?

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
3 minutes ago, WatchCodger said:

Is there such thing as a JDM SKX case, specifically? Is the case from an SKX007J made in Japan?

There is not, only the dial and rotor change on these.

3 minutes ago, WatchCodger said:

You can't get an SKX OEM case, seperately, now anyway.

You can, but at exorbitant prices. https://www.cousinsuk.com/category/filter/seiko-case-parts and search 7S26-0020.

3 minutes ago, WatchCodger said:

Fat spring bars should be about $6/pair from any seller. $22?

Sorry, $14 a pair on Namoki. Easy to find for much less any of their items.

Link to comment
Share on other sites
WatchCodger New Member

WatchCodger

Posted
Posted

So it sounds like, if someone is interested in an SKX-type case they can buy the exorbitantly priced "genuine article", which could be made in China -- or a high-quality aftermarket case, undoubtedly made in China, for a reasonable price. Given that the aftermarket options have proven their quality and value to me, I can recommend  them.

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 minutes ago, WatchCodger said:

So it sounds like, if someone is interested in an SKX-type case they can buy the exorbitantly priced "genuine article", which could be made in China -- or a high-quality aftermarket case, undoubtedly made in China, for a reasonable price.

Or buy a complete diver's for about $100 and if it's only for the case, have a lots of spare parts.

Maybe is just more practical to wear a complete, original Seiko watch as I had suggested before.

Link to comment
Share on other sites
  • 2 weeks later...
nlapietr Watch Enthusiast

nlapietr

Posted
  • Author
Posted
On 7/16/2020 at 1:45 PM, WatchCodger said:

There are now many suppliers of aftermarket cases for Seiko 72XX and NHXX movements. Have you looked up CrystalTimes? Theirs are  SKX-type (diver) cases that accept the parts you have (in addition to others required). Namokimods just announced "Rolex Explorer" style cases (two vintage sizes) that accept the parts you have. The later are currently pre-order. There are others as well.

My apologies if you've figured this out already!

Thanks.  I have not solved it yet and was just going to live with it.  I just find it ugly and will definitely look at these suggestions!

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...