Jump to content

Hairspring turning tool

gary17

By gary17
in Tools & Equipment

 Share

Recommended Posts

gary17 Super WRT Addict

gary17

Posted
Posted

Hi

I need to get a Hairspring turning tool. They seem to come in sizes. 

One end of the tool refits the Hairspring and they give you a size for the shaft size for this end. 

The other end let's you turn the spring collet and there seems to be no size for this end. 

What I need to know is which size should I get to get the most use from. 

Any help appreciated there not cheap to buy. 

Cheers

Gary

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I'm not quite sure what tool you are talking about, but if you are working on hairsprings and you haven't already got yourself one find yourself a good condition second hand staking tool as you can use this to refit hairsprings.

20190331_182012.thumb.jpg.17576cbbe9007b9f37ccf6db07a81192.jpg

Then to adjust the hairspring hang it on a balance tack

1750591577_balancetack.thumb.png.77be10970f7d29560bfe7af5acd1097f.png

And finally make this tool for adjusting the hairspring.

2074068442_hairspringtool.png.261058b69d595392975e7d9b481d390a.png

Mine was made from blue steel approx 2.5mm in diameter.

I went a bit crazy with the grinding on mine, you really just need to grind / file about the last 15mm from the end take it off from both sides so its is about 0.3mm thick (this can be bigger or smaller depending on the hairspring collet size) and then file the end as shown in the photo so it looks a bit like a tiny hockey stick.

The idea is you have worked out already if you want to rotate the hairspring to the left or the right and then you hang it on the balance tack and hold the balance wheel. As the tool is only 0.3mm thick turning it on its side you can slide it between the hairspring coils and then turn it 90 degrees so the end of the 'hockey stick' is facing towards the slot in the collet and you push it in the slot which loosens the collet and you can rotate the hairspring and then the remove the tool.

It may help to put a little wedge into the very end of the tool so it goes into the slot on the collet easier.

I hope that all makes sense.

 

  • Thanks 1
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

I think only Bergeon has them, and they give no indication what the actual sizes are. In the pic, the foreground is two commercial one (old, I believe Bergeon but unmarked), you can see what the two ends look like. The other two are shop made and double ended just for turning; I needed an extra small one and a larger one with an extra fine "finger".

 

I don't know what they cost but I'd say just buy the 5 that Bergeon sells, if you just get one or two you'll always need one you don't have.

 

Hairspring push turn.jpg

  • Like 1
Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

My mentor taught me to use an old oiler for this. Just use 1 big enough for the job. Wedge it in, give it a slight twist axially to open up the collet ever so slightly and turn collet to desired position.

It works. But I find that oilers tend to be a bit to flexible and getting the collet to zero beat error position a little difficult. Instead, I use a ground down sewing needle. I read it in a book by Henry Fried. Let me search for it and I'll post it later.

20200701_090225.jpg

20200701_093232.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...