Jump to content

Longines Dial search

clockboy
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

Approx. 3 months ago I serviced this really nice vintage longines watch. However the dial was badly stained/aged. The big mistake I made is I tried to clean it and if anything I just made things worse as some of inscription came off !!!. Anyway tale of woe over. Since then I have been searching for a replacement even a damaged one with absolutely no success. By any chance does anyone have any ideas where I could find a replacement. The dial size is 29.45mm

 

IMG_5497.thumb.jpg.7f38e176bcdb3a3ae2db65cb2dc2d811.jpg

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

I take it you have looked at all the normal places. It might mean you have to have the dial restored which will coat a lot. Have you tried longines  direct to see if they can help. Many years ago they used to be very good in helping out, I'm talking back in the 70's and 80's don't know about today. 

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
4 minutes ago, oldhippy said:

I take it you have looked at all the normal places. It might mean you have to have the dial restored which will coat a lot. Have you tried longines  direct to see if they can help. Many years ago they used to be very good in helping out, I'm talking back in the 70's and 80's don't know about today. 

I will try longines. I have tried all of the usual but no luck.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
21 minutes ago, FLwatchguy73 said:

I'm sure this one cost more than the entire watch, but It may be worth it for you. What model is the movement? Can help narrow down which dial.

Thanks watch guy. Unfortunately that one is not the same design. As far as the price quoted goes that is about right, and the customer is willing pay the going rate. 

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
3 hours ago, rodabod said:

Is this for a 12.68?

This movement is a 12.68ZS. However it is a 12 ligne caliber longines movement that also has variants with minor differences between 12L, 12.68N & this 12.68ZS.

 

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted (edited)

It looks very similar to the dial used on the Longines 30LS, although I'm guessing the dial posts are in different positions or the dial is slightly different size.

He is my 30LS

The second hand is not correct on my watch it should be like the one in your photo above.

dial.jpg

Edited by Tmuir
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
4 hours ago, Tmuir said:

It looks very similar to the dial used on the Longines 30LS, although I'm guessing the dial posts are in different positions or the dial is slightly different size.

He is my 30LS

The second hand is not correct on my watch it should be like the one in your photo above.

dial.jpg

I would say that is it if the dial is 29.45mm then it is a match.

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted
17 hours ago, clockboy said:

I would say that is it if the dial is 29.45mm then it is a match.

I've not uncased this movement yet and don't want to until I need to service it so can't properly measure the dial, but holding the vernier over the crystal the dial has got to be pretty close to that measurement, but I can't say for sure.

Uncased 30LS movements do turn up from time to time, but I've not seen one with a dial yet.

I'm on the lookout for the correct second hand for mine, if you do end up finding a movement with dial and it has hands I would be interested in buying the second hand off you.

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

Looking at the movements

http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&&2uswk&Longines_12_68ZS

http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&&2uswk&Longines_30LS

12.68ZS diameter is 27.5 and the 30LS is 30mm, but the dial holes in the movement look further in from the edge on the 30LS, but flicking backwards and forwards between the 2 movement pictures the holes look to be a couple of degrees offset from each other, so I'm not sure the dial from a 30LS would fit a 12.86ZS

 

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted

I have noticed this before with "ranfft" the pics shown are not always correct. The pic for the calibre LS is showing the calibre L. I did google and the LS movement looks the same as the ZS. Having said that the chances of getting one is now slim. Longines have been in contact and they suggest getting then dial refurbished. I have had a quote £140 ex. postage. If it was my watch I would go ahead as it is really nice Longines watch with a 9ct gold case and strap. BUT !!!!

Link to comment
Share on other sites
chrisdt WRT Addict

chrisdt

Posted
Posted

I personally don't think it looks bad as it is and I absolutely love those expanding bracelets. Excalibur 49 or 50 if I'm not mistaken. Did'nt think £140 was bad for a refurbished dial. The trouble is any you might find on line etc will probably be as bad if not worse than yours.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • RichardHarris123
      Any tips to correct a sloppy error?

      By RichardHarris123 · Posted

      Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
×
×
  • Create New...