Jump to content

Timex winding stem

HectorLooi
 Share

Recommended Posts

HectorLooi Distinguished Member

HectorLooi

Posted
Posted

I'm having trouble removing the crown off the winding stem of a Timex M27 movement. I've tried WD40, heating it with a torch, but the crown simply refuses to budge.

It doesn't appear to have any screw threads. Could it be friction fitted?

Any suggestions? 

20200606_110058.jpg

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
  • Author
Posted
2 hours ago, JerseyMo said:

I should have the part in stock.  What is the dial code printed below the 6 hour?

 

Thanks for the kind offer JerseyMo.

I picked up a compound slide a couple of weeks ago. This winding stem would be a simple project for me to break in my new toy. :D

Link to comment
Share on other sites
JerseyMo Distinguished Member

JerseyMo

Posted
Posted
8 hours ago, HectorLooi said:

Thanks for the kind offer JerseyMo.

I picked up a compound slide a couple of weeks ago. This winding stem would be a simple project for me to break in my new toy. :D

sure new toys are fun. let us know how you progress with the repair.

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
  • Author
Posted

I made some progress. I managed to get the old crown off by wedging the stem into the V shaped groove of a staking block and using 2 big screwdrivers as levers to lift the old crown off. Now all that is left for me to do is drill out the threads of a new crown and superglue the winding stem in. :woohoo-jumping-smiley-emoticon:

20200611_214525.jpg

  • Like 1
Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
  • Author
Posted

Wow. This 'simple project' is really fighting me all the way. No wonder JerseyMo's reply had a sprinkling of cynicism and skepticism. 

I got a new crown. The pipe was a little long. No problem, I filed it down.

The case tube was too big for the new crown. No problem, I put it in the lathe and cut the hole in the washer bigger. 

Then the oring in the crown was too small. I managed to get the crown washer out and got a new oring that fits. 

The only thing left was to drill out the threads and glue the winding stem in. :woohoo-jumping-smiley-emoticon:

Yeah. Right. The tungsten carbide drill bit broke in the hole. :pulling-hair-out:

 

20200617_100846.jpg

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
1 hour ago, HectorLooi said:

Yeah. Right. The tungsten carbide drill bit broke in the hole.

Looks like it can be pulled out. Carbide is not a good choice for a soft and catchy material, it would have to spin real fast with that small diameter. Better a regular HSS bit driven by hand. 

Edited by jdm
  • Like 2
Link to comment
Share on other sites
JerseyMo Distinguished Member

JerseyMo

Posted
Posted
14 hours ago, HectorLooi said:

Wow. This 'simple project' is really fighting me all the way. No wonder JerseyMo's reply had a sprinkling of cynicism and skepticism. 

the hard learned lessons are the best teachers. but they suck to have to live through!  Maybe I'll put that on a t-shirt!

  • Haha 2
Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
  • Author
Posted

Thanks JerseyMo. This is a '75 Telephone Dial Marlin. (26961 02775)

The case is in pretty bad shape. Almost all of the gold plating is gone. Even the underlying nickel layer is gone in some places. But the dial and movement are ok.

I don't think this watch can be restored to a state that I would wear it. I'll eventually turn a new stem for it when I have the time. But thanks again for the offer.

I managed to drill out the broken tungsten carbide tip with a diamond bur in a dental highspeed handpiece. But when I tapped the stem in to test it, the pipe split open. 

Looks like I'll put this on the back burner for now.

20200618_090806.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...