Jump to content

Tissot 7842

Hasnain
 Share

Recommended Posts

watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi   I have attached the tech sheets  for the tissot models  as there seems to be a lot of parts which are common across the range.  The balance complete is 720 without spring and 721 with spring attached, so by the fact it is supplied as a spare it is detachable.  the spring its self does not look too bad and most probably be re curved ok.  If you could supply a picture of the balance and cock laid upside down so members can see the attachment it would be a great help.       cheers

2790_Tissot 781.1,782.1,783.1,784.1 (4).pdf 2789_Tissot 781,782,783,784 (2).pdf 2791_Tissot 783.2,784.2 (1).pdf

  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

 W W is right, if you show a picture of the cock laid upside down, we have a chance to figure out how to detach the HS and if the collet is removable then sorting the HS out and shaping an end curve isn't a tough task. 

A top view with balance pivot inside the jewel hole, would be helpful.

 

  • Like 1
Link to comment
Share on other sites
Hasnain New Member

Hasnain

Posted
  • Author
Posted
3 hours ago, watchweasol said:

Hi   I have attached the tech sheets  for the tissot models  as there seems to be a lot of parts which are common across the range.  The balance complete is 720 without spring and 721 with spring attached, so by the fact it is supplied as a spare it is detachable.  the spring its self does not look too bad and most probably be re curved ok.  If you could supply a picture of the balance and cock laid upside down so members can see the attachment it would be a great help.       cheers

2790_Tissot 781.1,782.1,783.1,784.1 (4).pdf 2.84 MB · 0 downloads 2789_Tissot 781,782,783,784 (2).pdf 4.14 MB · 0 downloads 2791_Tissot 783.2,784.2 (1).pdf 1.26 MB · 0 downloads

Thanks for the response heres an image 

P6041188.JPG

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • RichardHarris123
      Any tips to correct a sloppy error?

      By RichardHarris123 · Posted

      Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
×
×
  • Create New...