Jump to content

A little help opening this watch

dormantkerosene
 Share

Recommended Posts

VWatchie Distinguished Member

VWatchie

Posted
Posted

Getting a snap-on case back off using a blade can be very efficient but requires some dexterity and there's a risk you'll scratch the watch and/or hurt yourself if you slip. I use a blade myself but to me it's a pain every time so for that reason I try to stay away from snap-on case backs. It can also be a pain to replace the case back. It's not always possible to press it back by hand and in those cases a crystal press is needed.

I've just ordered a tool designed to remove snap-on case backs and bezels. I primarily ordered it to remove bezels. I don't know if it is any good. It was inexpensive (unlike most watch tools), so I decided to take a chance. Click here to see it. You can get it for less if you take it from China or AliX.

Good luck!

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 hours ago, dormantkerosene said:

As. you can see with the indentation, it's faded out and I can't pry the watch back open. What should I do?

It would probably come off using properly a dressed knife and sturdy case holder into the hands of an experienced person, but it's also true, as noted above, that these can be really tight and difficult to deal with,
The specialized tool also mentioned is the one that I covered in a previous thread below, I suggest that you search the forum a next time, most question have been asked and answered before. Also, very likely that you will also need a case press to close it, all in all it may be much less expensive and complicated to give it to a watch shop.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • RichardHarris123
      Any tips to correct a sloppy error?

      By RichardHarris123 · Posted

      Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
    • mikepilk
      Setting lever spring

      By mikepilk · Posted

      The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      🤔 what happens if lubrication is placed directly on top of epilame ? Making a small groove so the lubrication doesn't spread across the component but what if when lubing a little overspills and sits on the epilame .
×
×
  • Create New...