Jump to content

Dial Cleaning

jdrichard
 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
Posted

Working on a Hamilton 992 with a dirty dial. A fine cleaning with Rodico followed by targeted removal of spots and blotches with a toothpick; and then a cleanup with Rodico and Ta Da.

852b50ca2bddd21baf4da6b54276cf33.jpg43e69ac00b8dfc654451c9f635fb0ca8.jpgf9c756ba0c960b12443ba4ac073929e2.jpg

And the movement was cleaned with Rodico as well. Being very careful not to touch the jewel holes. This PW has a swing of 540 Degrees.

00df030354393e242541aaa4cc6d345d.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 5
Link to comment
Share on other sites
Marc Distinguished Member

Marc

Posted
Posted
8 hours ago, spectre6000 said:

How does that work?

Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

  • Like 2
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

Thanks Marc. I usually use my iPhone in slo-mo to observe the swing. I also bought eTimer for looking closely at the performance. Would it be possible for you to make a video on how to use eTimer for diagnosing watch problems. Their manual is not sufficient.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
spectre6000 Distinguished Member

spectre6000

Posted
Posted
9 hours ago, Marc said:

Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

 

4 hours ago, jdrichard said:

360 plus 180 :) Full swing. Amplitude is 1/2 that value

Right. Duh. I read it as amplitude. Don't usually see it stated in terms of full swing. Opposite of BPM and Hz. I think in Herz, but it's always stated in terms of BPM. 

4 hours ago, jdrichard said:

No. Used a toothpick to remove the yellow stuff!! Then cleaned up with Rodico.

So, you scraped every square mm of the dial with a toothpick, and yellow schmutz came off? Interesting... Seems like that's a porcelain dial-only strategy. 

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
So, you scraped every square mm of the dial with a toothpick, and yellow schmutz came off? Interesting... Seems like that's a porcelain dial-only strategy. 

I scraped those areas with significant blemishes or moisture bumps, but I did do the whole dial carefully with Rodico


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
  • 8 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base, I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded. The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool. Note, I think you may need to print supports for the new internal shelf created? Modular Movement Holder v2.pdf Modular Movement Holder v2.pdf
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking. 
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Good job, that band matches the watch perfectly.
×
×
  • Create New...