Jump to content

Dial Cleaning


Recommended Posts

Working on a Hamilton 992 with a dirty dial. A fine cleaning with Rodico followed by targeted removal of spots and blotches with a toothpick; and then a cleanup with Rodico and Ta Da.

852b50ca2bddd21baf4da6b54276cf33.jpg43e69ac00b8dfc654451c9f635fb0ca8.jpgf9c756ba0c960b12443ba4ac073929e2.jpg

And the movement was cleaned with Rodico as well. Being very careful not to touch the jewel holes. This PW has a swing of 540 Degrees.

00df030354393e242541aaa4cc6d345d.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 5
Link to comment
Share on other sites

8 hours ago, spectre6000 said:

How does that work?

Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

  • Like 2
Link to comment
Share on other sites

Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

Thanks Marc. I usually use my iPhone in slo-mo to observe the swing. I also bought eTimer for looking closely at the performance. Would it be possible for you to make a video on how to use eTimer for diagnosing watch problems. Their manual is not sufficient.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

9 hours ago, Marc said:

Total arc of swing from extreme clockwise point to extreme anti-clockwise point is double the amplitude. So a swing of 540 degrees is an amplitude of 270 degrees. 

 

4 hours ago, jdrichard said:

360 plus 180 :) Full swing. Amplitude is 1/2 that value

Right. Duh. I read it as amplitude. Don't usually see it stated in terms of full swing. Opposite of BPM and Hz. I think in Herz, but it's always stated in terms of BPM. 

4 hours ago, jdrichard said:

No. Used a toothpick to remove the yellow stuff!! Then cleaned up with Rodico.

So, you scraped every square mm of the dial with a toothpick, and yellow schmutz came off? Interesting... Seems like that's a porcelain dial-only strategy. 

Link to comment
Share on other sites

So, you scraped every square mm of the dial with a toothpick, and yellow schmutz came off? Interesting... Seems like that's a porcelain dial-only strategy. 

I scraped those areas with significant blemishes or moisture bumps, but I did do the whole dial carefully with Rodico


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

  • 8 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...