Jump to content

Making a Watchmaker's Bench


Recommended Posts

With anticipation and excitement my new, not inexpensive bench showed up last night.  I'll mention no names, no vendors.  Let's say the bench looks absolutely amazing on the internet.  Much like the difference between the bacon double cheeseburger pictured on the menu, and the one you get in the paper--the bench's wood was old and dry, split, filled here and there with "wood filler" that was terribly off-color, warped, out of square, and indescribably unsatisfactory.  A refund is forthcoming.  While that gets sorted out. . . 

I went to a store today and bought materials and tools to get started on the drawers and their encasements.  I'll start uploading pictures as the project progresses, but I'm going to make a bench that's about 3' 2"high,  4' wide, and 21" deep.  The top will have rear and side rails.  I'll have 9 drawers on the right, a few on the left, and a large, felt-covered pull-out "shelf" area in the middle, which will be covered by the bench top when not extended.  

I'm going to give box-joints a go for the drawers. I'm no carpenter, but with the information available I should be able to make something I'll be proud of, and will last a lifetime. 

I'll keep a diary here as things progress.  It will be nice to get off the kitchen table.  The wife will be pleased. 

Edited by SparkyLB
  • Like 1
Link to comment
Share on other sites

Day one.  Materials.  I'm in a little over half the price of the bench I bought, and have a new Kreg Jig, Dado Stack, and 4' clamps.  I estimate I have about 50% of the lumber I need from this first purchase.  If the past is any indication of the future, I'm in possession of about 30% of the lumber I need.  :)    

Time to make the drawers.  Today I'd like to make both left and right drawer encasements, and all drawers. 

508846809_dayonematerials.jpg.e32c846690863569cc541f00bb413ebf.jpg

Edited by SparkyLB
Link to comment
Share on other sites

If it were a construction site I'd be fired.  An 8-hour day and one successful joint to show for it.  I had to tweak the jig and lots of trial and error before I got my tools to behave.  Having that behind me, the rest of the drawers will take far less time. 

So my 14 drawers will be box jointed just like this. 

991121240_firstjoint.jpg.9d8e1fc26e9333a43b5521cc831a512a.jpg

  • Like 4
Link to comment
Share on other sites

it's unfortunate that something that can look so pretty in a picture can turn out very poor. On the other hand it's an opportunity to make something much nicer. Like for instance when I'm doing this I'm looking at my computer and the desk I made so it fit the space that I had it met my requirements because I couldn't find anything that was suitable for a computer desk for me.

As much as I like my watch bench I would really like modifications like it would be nice to have drawers on both sides of the bench. The entire left-hand side is open and basically it's wasted space. when you're starting out it seems like the bench is a vast open space but it's amazing how fast it gets filled up and then you run out of space.

 

 

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

Hi John.  Yes it's unfortunate but as you say, an opportunity.  When I'm finished (it seems in about 7-10 years) I'll have a bench that I would not have access to with my means; not to mention shipping costs.  I'll know what everything is made of and at the very least, it's ALL real wood, and high quality woods.  Small touches like inexpensive hardwood 5mm plywood for drawer bottoms make it special to me.  This particular ply has real wood grain that you don't generally see. 

watchweasol, thank you.  I made a box joint jig.  I'm using a radial arm (chop) saw to cut items, and a circular saw table for the jig/box joints.  A router was on my list, but only for the skirting material on the sides and back of the work surface.  I wound up not getting one, as there's no shortage of ornate moldings and trim that are already routed somewhat closely to what I envisioned. 

I might still get a router and put a radius on the drawer false-fronts, the work surface adjacent to me, and the 4 vertical edges.  If it will enhance the utility and appearance, I'm all for it. 

One thing I need is a planer for the box joints.  Either that or a belt sander to make quick work of it. 

This is an evolution, and I'm sure will change as I go along. 

Edited by SparkyLB
Link to comment
Share on other sites

Fantastic work so far.
If you have the skills and tools to make it yourself the end result is always far more satisfying than a cheap off-the-shelf solution and you get something built to your specific needs.
I commend you for doing drawers, they're fiddly and time-consuming.


Sent from my iPhone using Tapatalk

  • Thanks 1
Link to comment
Share on other sites

10 hours ago, tritto said:

Fantastic work so far.
If you have the skills and tools to make it yourself the end result is always far more satisfying than a cheap off-the-shelf solution and you get something built to your specific needs.
I commend you for doing drawers, they're fiddly and time-consuming.


Sent from my iPhone using Tapatalk

Indeed they are.  I'm also working with a cheap table saw whose runners have a lot of slop.  I'm going to make my own runners later today out of hardwood.  The jig should give more repeatable results.  The top 7 drawers are all 2 1/2" high.  The bottom two will be larger, with the very bottom being 7" to accommodate my staking set box. 

I think I'll use thicker fingers on the bottom two, larger drawers.  It will be a nice variation. 

  • Like 1
Link to comment
Share on other sites

Impressive! :thumbsu:

Saying the following is probably like swearing in church, but I use a simple but steady electrically elevated and lowerable table as my workbench (IKEA I think, yes I'm Swedish). I find it extremely convenient depending on what I'm doing, for example fitting the balance cock (elevated) or when I need a "helicopter" perspective (lowered). It quickly goes up and down with a simple press on a button. I'm so used to it that I don't even think about it.

Then again, I don't use eye loupes either but magnifying glasses and a stereo microscope. I would never be accepted among real watchmakers :( Anyway, I'm truly impressed!

  • Like 1
Link to comment
Share on other sites

amazing work, well done. The heavy drawers are a bit overkill imo but it really looks good. Like Vwatchie I was looking for the Ikea Bekant table which was around 450 euro but I was able to buy a watchmakers heritage with a few professional workingbenches and a ton of parts. Sadly the family, who were not in contact with their father, only had eyes for the gold and gemstones and had already thrown away at least 20 movingboxs full with parts, books, tools ect....

  • Like 1
  • Sad 3
Link to comment
Share on other sites

Here is the right side drawer encasement with drawers.  Making the bench satisfactorily is consuming a lot of time, but I have no regrets.  I enjoy the work.  I think after the drawer-fronts are done and pull-handles installed I will make the back, and left/right sides of the bench.  Then I can take it inside and have a surface on which to work; while I complete the left-side encasement and drawers.  It might take some months; but I know when it's finished I will have known I did my best on everything. 

305179965_leftsideencasementanddrawers.thumb.jpg.b4fcf75baad181b346deb4d475ccfd8f.jpg

  • Like 4
Link to comment
Share on other sites

I'm no furniture maker, but I think this will work.  First milestone complete.  Next is the back and sides, then the working surface.  I'll then bring it in and make the other case of drawers at a less hurried pace. 

  handles.jpg.4b9f80f84fc29c82f15e0bd5b3617ee2.jpg

1486671286_handles2.jpg.f1f06910617f534652e1335cf9f8179d.jpg

  • Like 4
Link to comment
Share on other sites

Nice years ago I made a jarrah bench for my workshop, (just a workshop bench, not a watchmaker's bench) used a thicknesser to get the jarrah all to the same size and then hand planed the bench top flat once glue up, my wrist hurt for a week. My wife walked into my workshop and asked me when I was making her a kitchen table like that. I told her 'Never'. Your watchmakers bench is coming along nicely.

  • Thanks 1
Link to comment
Share on other sites




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Looks that way, if it had any amount of significant jewel count it would say so on the dial.    Looks that way, if it had any amount of significant jewel count it would say so on the dial.  Same answer as Mike regarding the dial, its often just a slapped on name of a retailer but i thought you were way above this understanding Pete ?
    • Light naptha is what you need to be looking for. The carbon to hydrogen ratio is high with heavy naptha, it doesn't evaporate as well as light naptha and is prone to leaving more residue. Try tom's suggestion of the mirror test.
    • Its a big item Michael and a lot that could go wrong with the process of getting it to its new location. I once helped install one of these units into a conservatory that i had built. It was big and bloody heavy and took six of us to get it in safely. If you have sliding doors and you need to remove the whole frame then that may or may not go well. But i would advise getting a professional in if you have little knowledge on the installation of them. The glazing of the doors could well be 6mm laminated glass which again will be heavy very heavy if the glazing units are big. The glass would also need to be set up and packed correctly to open the doors properly more so if they are unframed and the sliders are upvc. Seems a shame but if no one is biting and that may be due to having no warranty i guess the only takers might be someone that installs them for a living and knows how to repair. If its fibreglass just be careful, i sometimes have to cut fibreglass baths out and they are nasty to work with . Thick gloves are definitely recommended,  not fun picking out fibreglass spells two days later that have started to go septic. Good luck with it all matey.
    • I don’t know anything about this product, however assuming you have it if you put a drop on a mirror or piece of glass lying flat on a table and leave it to evaporate if it leaves any sort of residue it is not really suitable for watch part cleaning.   Tom
    • Well I put the spa on Gumtree (selling service) to try and sell it as it only needs a recirc pump to get it going. However, it weighs circa 250kg, so there's 4 fairly strong guys, and I would have to remove the sliding door in the room completely to be able to get it out, as well as clearing out a multitude of potted plants and the Alfresco outdoor setting to be able to get it out. Then move nearly everything in the back of the garage to be able to push it through to the front of the house. I would also need to hire furniture skates to be able to shift it around as carrying it is out of the question. Then someone would need a trailer to get it to their place as you won't get it on the back of a ute. So, the only answer is, out with the reciprocating saw and cut it all up into manageable pieces. Crying shame as it is in really good nick. I was only asking $1,500 and only got two bites, but it would only take something to go wrong with removing the sliding door etc that everything I make on the sale could go out the door on repairs etc. It would have been nice to be able to turn it into tools etc, but que sera sera. I don't know about the rest of the world, but there just seems to be very little interest from people wanting to buy things secondhand.  
×
×
  • Create New...