Jump to content

1 inch = 1 inch = 1 inch

jdm

By jdm
in Tools & Equipment

 Share

Recommended Posts

JohnD WRT Addict

JohnD

Posted
Posted (edited)

With a conventional mechanical micrometer, like the ones shown, while the zero point with the anvil closed can be set up by the operator using the small 'C' spanners usually provided with the instrument,  the ultimate accuracy along it's operational measuring length is determined by the pitch accuracy of the lead screw in the barrel, there is usually means of tightening the nut to lead screw pressure with an adjustable collet arrangement on the nut. If you are attempting to work to tenths of a thousandths of an inch, ambient temperature will make a small difference to accuracy.

I have this fairly ancient 'Draper' 0-4" caliper mic. set that has the replaceable anvils and the set up test pieces, which specify length accuracy at 20 degrees C.

Draper micrometer.jpg

Edited by JohnD
Link to comment
Share on other sites
JohnD WRT Addict

JohnD

Posted
Posted (edited)

Just did some tests on my Roebuck digital caliper, using the Draper test pieces....

For each test I closed the caliper first and checked the 0.000" reading then opened it up and placed the test piece in and closed it till it was lightly clamping it...

1" Test.... spot on

 

2" Test....minus one thou

 

3" Test....minus 5 tenths of a thou

Ambient temperature 28C

Quite pleased with this :thumbsu:

 

 

Roebuck caliper 1 inch test.jpg

Roebuck caliper 2 inch test.jpg

Roebuck caliper 3 inch test.jpg

Edited by JohnD
Link to comment
Share on other sites
JGrainger WRT Addict

JGrainger

Posted
Posted

I literally just watched this comparison video the other day between watching videos on casemaking.. I'd have liked to have seen a comparison done on both sets of jaws as internal measurement is often less nice than external. The cheap measuring tools are good enough for their purpose.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • dnhb
      Beat adjustment

      By dnhb · Posted

      I'd be grateful for recommendations of good sources of advice on getting clocks with balance spring - as opposed to pendulum - escapements 'in beat'.....
    • Michael1962
      Hettich Clock

      By Michael1962 · Posted

      Well I am in a bit of a quandary. I can't find the correct colour for the dial. I even wrote to Hettich a while back hoping they would give me the colour code for the dial. The reply that I received was "We don't make those anymore." I am thinking now to silver the dial and use a water transfer decal to put minute markers and the HETTICH logo (which is the very font that this forum uses) and the Made in Germany down the bottom. Not sure of the success rate of the water transfer method, but I have no other solution for the markers and logo. Handpainting is just not an option. In trying to get the top piece of the clock polished, it has progressively lost its sharp edges. My stupid hamfisted effort. I am thinking of purchasing a replacement piece of brass and drilling new holes in it for the corner posts. Why I attempted to repolish using wet & dry and not simply using a paint remover to remove the old lacquer from the brass, I don't know. You whistle and I'll point at the idiot. I also need to purchase some sheet spring steel as the two small ratchet springs that arrest the wheel that supports the weight after it is lifted by the electromagnet are worn. The two from the donor clock that I purchased are worse. I am hoping that I will be able to manufacture new springs without having to fiddle about with tempering etc to the steel. I have some ideas on that front. How many things until the clock is no longer the original? Like an axe. Heard a woodchopper on tv once saying that he had replaced the head on his axe twice and the handle three times, but it was the same axe that he began woodchopping with. 😉
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      I use the exact OD and it fits in with a little force and a pleasing 'click' so it's snug and wont rotate within the holder, but that depends on how you have set up and calibrated your printer so you may need to play with the settings/dimensions a little to allow for any discrepancies in your printer calibration. PS I just finished (2 days ago) a new revision which automatically prints the movement OD on the bottom of the holder, I'll see if I can upload it here Here is rev 4 remember to change the .pdf to .FCStd so it will open in FreeCAD - also you may need to install the LiberationSansBold font and tell FreeCAD where it lives on your PC, or change the font to something you already have on your system. Para Movement Holder V4.pdf
    • Waggy
      Tool of the day.

      By Waggy · Posted

      Only someone on this forum would ever understand the Oooooo I just did
    • Zedster
      Movement holder made with 3D printer

      By Zedster · Posted

      Hi, guys I'm very interested in printing out this design as I've seen the orignals used on many occasions and I'm fed up with my movements popping out the standard Bergeon type so want to give this type a go 😀  As I've never used this type before should the movement be a snug fit in the holder? Once you've measured the diameter of the movement do you put this exact value in the spreadsheet or increase it a little 🤔 Comments would be appreciated 👍  
×
×
  • Create New...