Jump to content

Watch stops when canon pinion tight


Recommended Posts

Hi

When I loose the canon pinion, it obviously doesn't turn the minute hand. When I tighten it, the watch either runs poorly or stops in a low power reserve. Movement Universal 129. What am I doing wrong? :blink:

Image attached with canon pinion displaced. 

Kind regards. 

20200513_153208.jpg

Link to comment
Share on other sites

probably too tight, excessive tightening in effect integrates canon and the arbour into one piece. Canon pinion is suppose to turn on the arbour it is mounted on, to set the time. first thing to do in case you haven't already is to put some oil in the canon and turn . If no good you would need to broach it.

  • Like 2
  • Confused 1
Link to comment
Share on other sites

The canon pinion is fairly easy to remove with a tweezer, so it shouldn't be too tight. :unsure:

Actually, the watch runs very good when canon pinion removed.;)

Edited by Khan
Link to comment
Share on other sites

If canon pinion is too tight, it sets the enitre min train  to move.

I eliminate gears from canon pinion on to the end of min train one at a time and make sure posts the gear sits on are not loose, further I grab the canon pinion , shake see if it feels loose inside the center hole.

 

 

 

Link to comment
Share on other sites

On 5/13/2020 at 10:38 PM, JohnR725 said:

how does the watch run if the canon pinion is on but the minute wheel is removed?

It looks to run as good as when canon pinion removed. The watch now starts with a couple of winds. 

  • Haha 1
Link to comment
Share on other sites

2 hours ago, Nucejoe said:

Could be the bridge on minute train pushing down on gears,  just to test I loosen the screws on the bridge.

I tried that and it runs remarkably better when the screws not tightened at all but just turned into place. I'm now testing the power reserve and see how it goes. 

Link to comment
Share on other sites

Great,  I check the min train birdge for sign of gear rubbing on it,  you can shim the bridge or attack with sand paper or a flat face chisel, whatever approach that suits you to eliminate the rubbing.

Good luck.

  • Thanks 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Ok thanks Ross, I will give that a try!😁
    • Welcome my friend. 
    • Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
×
×
  • Create New...