Jump to content

Fixing my Late Brothers Watch


Recommended Posts

This watch was working up until recently when the stem came out. I can still insert the stem & wind but cannot set it.

I've tried all local watchmakers without any help. The Factory advised it was a 60's branded watch made here in the States.

I would love to get it repaired...fond memories require it.

Any help greatly appreciated.

G.B.

fullsizeoutput_2bc4.jpeg

fullsizeoutput_2bc1.jpeg

Link to comment
Share on other sites

My condolences GB. To keep busy with watchrepair, the watch is very likely to be undamaged, just the set lever and set spring are disengaged or broken set spring at worst. I am using an old Ipad right now which can,t access the pix you posted. All needed is a close up of the keyless, you would need to remove the hands and dial plate to uncover the keyless. Best wishes Joe

Link to comment
Share on other sites

Its a valuable watch that obviously has great sentimental value for you as well so I would not recommend doing anything yourself to the watch a picture of the stem would help a great deal of these watches where one piece cases and the stems where what would be termed a split stem.

Any competent watchmaker should be able to work on these watches.

Link to comment
Share on other sites

That case looks to be what is called a monocoque case, aka one-piece. As Nucejoe says, it's probably simple. However, for a newbie the case will present a difficulty. The crystal has to be removed by using with the right sized clamping tool or blown out through the pendant/pipe, where the stem goes in.

It looks like a very nice quality, and quite striking looking, dress watch. Any jeweler/watchmaker that does anything other than replace batteries and sell earrings should know that it's a once-piece case that takes special treatment, but is not daunting. Sorry about your losing your brother.

Mark Lovick, the guy who runs this forum, has videos on youtube under thewatchrepairchannel. He shows how to improvise to blow the crystal out. That said, once it's out, you do need a special tool to get it back in. Good luck.

  • Like 1
Link to comment
Share on other sites

My WAG is that both pieces came out and then they came apart. I certainly could be wrong. Regardless, the movement will have to be removed in order to make it right again. You don't want to lose those stem halves, as they are rather hard to find.

Despite the job being pretty straightforward for someone who has worked on watches a bit, it's not a good job to attempt yourself. Especially on a watch with sentimental value. If you have to remove the dial to get to the set-lever that engages with the stem, there's a good chance of damaging that very nice dial and/or hands. And when you damage the dial yourself  you never forget it. Every time you look at the watch and see the scratch(es), you'll be reminded. Don't ask me how I know.

 

Link to comment
Share on other sites

Here is all I know of the origins of the watch...I contacted what is left of JJ..

Thank you for the photos of your watch. I fully understand and appreciate its sentimental value and it appears to be in good condition. Unfortunately it’s US produced and we have no spare parts for it. However, I believe the watch is fitted with a standard Swiss movement and a local US watchmaker should be able to replace the broken stem.

Best regards,

 HANS RYSER

 Senior Advisor & Brand Ambassador

Just not sure yet how I should proceed.  

GB

 

Link to comment
Share on other sites

Was the watch running before the stem pulled out? If so, it's likely that there are no parts needed. If there are parts needed, and it's a generic movement as JJ says, you should be able to get parts. If it needs a mainspring I'm sure the right size and type could be found. I don't know why you're getting a bit of a run around with it.

You just need to find a capable watchmaker (Doesn't have to be an old master.) who wants to help you. It doesn't look like a tall order to me.

Link to comment
Share on other sites

11 hours ago, GomBoo said:

Western NYS...

GB

Just find someone local who seems like a real watchmaker and not a battery-replacement person. The NAWCC may have a list of reputable repairers in the USA. Otherwise, there are other Americans here who I’m sure will offer advice. 

Link to comment
Share on other sites

It appears that the old saying, "If you want something done right, do it yourself", has become "If you want something done, period, do it yourself".

In a state like NY, you shouldn't have to work so hard trying to give somebody a bit of money for watch service.  Strange times.

Link to comment
Share on other sites

Probably assembled  here.with a standard  or perhaps  more elaborate swiss movement.  Worth your time.as it is a nice watch with sentimental  value. I would  suggest that while having it repaired  you have it cleaned  and lubricated  as well. The stem is held in place by a lever which may be broken.my first guess would  be corrosion. The watch is stuck in the wind position. When an attempt to set it was made the lever snapped. But this is only a guess..any competent watch repairer  can do it. Unfortunately  I can reccomend  no one. If you do an image search on keyless works you should  be able to see how it works.it isn't at all complicated 

Edited by yankeedog
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
×
×
  • Create New...