Jump to content

Fixing my Late Brothers Watch

GomBoo

By GomBoo
in Watch Repairs Help & Advice

 Share

Recommended Posts

GomBoo Watch Enthusiast

GomBoo

Posted
Posted

This watch was working up until recently when the stem came out. I can still insert the stem & wind but cannot set it.

I've tried all local watchmakers without any help. The Factory advised it was a 60's branded watch made here in the States.

I would love to get it repaired...fond memories require it.

Any help greatly appreciated.

G.B.

fullsizeoutput_2bc4.jpeg

fullsizeoutput_2bc1.jpeg

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

My condolences GB. To keep busy with watchrepair, the watch is very likely to be undamaged, just the set lever and set spring are disengaged or broken set spring at worst. I am using an old Ipad right now which can,t access the pix you posted. All needed is a close up of the keyless, you would need to remove the hands and dial plate to uncover the keyless. Best wishes Joe

Link to comment
Share on other sites
wls1971 Distinguished Member

wls1971

Posted
Posted

Its a valuable watch that obviously has great sentimental value for you as well so I would not recommend doing anything yourself to the watch a picture of the stem would help a great deal of these watches where one piece cases and the stems where what would be termed a split stem.

Any competent watchmaker should be able to work on these watches.

Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

That case looks to be what is called a monocoque case, aka one-piece. As Nucejoe says, it's probably simple. However, for a newbie the case will present a difficulty. The crystal has to be removed by using with the right sized clamping tool or blown out through the pendant/pipe, where the stem goes in.

It looks like a very nice quality, and quite striking looking, dress watch. Any jeweler/watchmaker that does anything other than replace batteries and sell earrings should know that it's a once-piece case that takes special treatment, but is not daunting. Sorry about your losing your brother.

Mark Lovick, the guy who runs this forum, has videos on youtube under thewatchrepairchannel. He shows how to improvise to blow the crystal out. That said, once it's out, you do need a special tool to get it back in. Good luck.

  • Like 1
Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

My WAG is that both pieces came out and then they came apart. I certainly could be wrong. Regardless, the movement will have to be removed in order to make it right again. You don't want to lose those stem halves, as they are rather hard to find.

Despite the job being pretty straightforward for someone who has worked on watches a bit, it's not a good job to attempt yourself. Especially on a watch with sentimental value. If you have to remove the dial to get to the set-lever that engages with the stem, there's a good chance of damaging that very nice dial and/or hands. And when you damage the dial yourself  you never forget it. Every time you look at the watch and see the scratch(es), you'll be reminded. Don't ask me how I know.

 

Link to comment
Share on other sites
GomBoo Watch Enthusiast

GomBoo

Posted
  • Author
Posted

Here is all I know of the origins of the watch...I contacted what is left of JJ..

Thank you for the photos of your watch. I fully understand and appreciate its sentimental value and it appears to be in good condition. Unfortunately it’s US produced and we have no spare parts for it. However, I believe the watch is fitted with a standard Swiss movement and a local US watchmaker should be able to replace the broken stem.

Best regards,

 HANS RYSER

 Senior Advisor & Brand Ambassador

Just not sure yet how I should proceed.  

GB

 

Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

Was the watch running before the stem pulled out? If so, it's likely that there are no parts needed. If there are parts needed, and it's a generic movement as JJ says, you should be able to get parts. If it needs a mainspring I'm sure the right size and type could be found. I don't know why you're getting a bit of a run around with it.

You just need to find a capable watchmaker (Doesn't have to be an old master.) who wants to help you. It doesn't look like a tall order to me.

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted
11 hours ago, GomBoo said:

Western NYS...

GB

Just find someone local who seems like a real watchmaker and not a battery-replacement person. The NAWCC may have a list of reputable repairers in the USA. Otherwise, there are other Americans here who I’m sure will offer advice. 

Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

It appears that the old saying, "If you want something done right, do it yourself", has become "If you want something done, period, do it yourself".

In a state like NY, you shouldn't have to work so hard trying to give somebody a bit of money for watch service.  Strange times.

Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted (edited)

Probably assembled  here.with a standard  or perhaps  more elaborate swiss movement.  Worth your time.as it is a nice watch with sentimental  value. I would  suggest that while having it repaired  you have it cleaned  and lubricated  as well. The stem is held in place by a lever which may be broken.my first guess would  be corrosion. The watch is stuck in the wind position. When an attempt to set it was made the lever snapped. But this is only a guess..any competent watch repairer  can do it. Unfortunately  I can reccomend  no one. If you do an image search on keyless works you should  be able to see how it works.it isn't at all complicated 

Edited by yankeedog
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      Its 4 o'clock in the morning here in the Uk, i cant sleep, i dont sleep, not much ever really. My brain never shuts off to rest, I'm just a constant thinker, i have to be very tired to be able to sleep,  i guess eventually it will be my undoing and my health will suffer because of it I'm sure. But while I'm here i want to get as much out of life as i can, and give as much as i can, to help,maybe to make a difference to someone's life if that is within my capability,recent events have made that need even more clear to me. I'm not sure where I'm going with this or why i bring it up , or if its relevant to want i want to talk about its just in my head right now. What i do want to talk about is something thats been on my mind for ages. I like to be prepared,  I'm not fond of surprises because surprises take control away and i am a bit of a control freak at times. This forum, Our Forum if i can call it that, is here because of two reasons. The guy that created it and keeps it funded and the people that joined it.  Without either, it would not exist, and lets face it one day it won't ( I'm a realist and i talk about things others dont or who are afraid to in other words folk that dont particularly prepare for the inevitable). How many of us visit here regularly ?  How many among us almost depend on the forum as a way of socialising because they are stuck at home and how many of us has it become part of a daily routine to check in and see if they can offer advice or get help with something they are working on or just to have a chat and engage in some banter. The members here are in the thousands and thousands have disappeared over the years many had just a fleeting visit. But there are a good few of us that know each other quite well and visit regularly. I dont know about you but i wouldnt want to lose that communication with you all, in all honesty it has become an important part of that side of my life and helps to feed my passion for all things watches. Some of you may think differently and thats ok, some of may stop and think # what would i do " Without Our Forum " # 
    • Neverenoughwatches
      Gamblin Gamsol for cleaning?

      By Neverenoughwatches · Posted

      Naptha appears to be a general name and its content can be varied depending upon what it's specific use is. Lighter fluid as an example can be light or heavier also with other ingredients to help it burn. Try sesrching for benzine ( as opposed to benzene which is linked to causing health issues ) . There are other fluids such as ethanol that you could try and also methylated sprirts, mostly ethanol with a small percentage of methanol added. Experiment with any new chemical to see how quickly schellac dissolves in its presence. I have tried a few things but hexane is not one of them, i understand it does evaporate very quickly.  Be sure sure to check out any safety data on chemicals you try. Toxicity of fumes and flash point information, ultrasonic machines can heat up fluids even without a heater function. And of course always ask here for personal opinions when trying a new substance. 
    • GuyMontag
      What tools does ebay have to offer this week.

      By GuyMontag · Posted

      I have that set and really like it. I prefer that crystal holder over the one that came with my Bergeon claw tool and any time I use the claw I use this one instead of the Bergeon one, just an additional bonus with this tool.
    • GuyMontag
      Movement inserted from crytal side

      By GuyMontag · Posted

      Is the Roamer not a split stem? I'm confused on your how your case is put together. If it is a front loader where is it you are putting the case screws? I love me some Roamer, do you have any photos?
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
×
×
  • Create New...