Jump to content

Dial wear and tear

AllyK83

By AllyK83
in Watch Repairs Help & Advice

 Share

Recommended Posts

AllyK83 New Member

AllyK83

Posted
Posted

Hello, I am new to the forum, and am looking forward to learning from the experiences and expertise held by everyone here, so thanks for having me! 
I have acquired a Rolex Oyster Speedking, circa 1964, that appears to run well. However, I have noticed that there is some wear to the edge of the dial between the 10 and 12 area. It looks to be dry, but wondered if it is a result of staining, moisture or oil from the movement? Also, would it be some that is likely to deteriorate? I have attempted to attach a photo, which is probably the best way to describe my question. Thanks again for your help. Ally

 

B8C530C2-E188-4818-BEE2-46ECEAE1FC0B.jpeg

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
2 hours ago, AllyK83 said:

I have acquired a Rolex Oyster Speedking, circa 1964, that appears to run well.

Even it runs well, not knowing its service history or a least looking on a timegrapher or equivalent application will expose you to the risk that is running on dried oils, that will increase a lot the wear of pivots and stones and may cause expensive repairs at a later time, so if you intend to have it running and preserve its value the best would be to bring it to reputable watchmaker for a full service.

Quote

However, I have noticed that there is some wear to the edge of the dial between the 10 and 12 area. It looks to be dry, but wondered if it is a result of staining, moisture or oil from the movement?

I think it's simply the old base or paint decaying and flaking off. You should check if it is at least stable because having debris around wouldn't be good at all.

Edited by jdm
  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
2 hours ago, AllyK83 said:

Thanks for the replies and advice. In your opinion, is the dial repairable, without a complete redial being necessary? Thanks 

It all depends when the watch is out of its case. There could be a little flaking that we don't see. I would still say yes. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Without Our Forum

      By watchweasol · Posted

      Hi guys, the question is what is a forum, a place for discussion and passing on information, idle chat and a bit of fun and I for one are the richer for it. When in Hospital last year with the Covid being force fed oxygen and feeling total sh1t and close to the pearly gates a daily look on the forum to see what was going down helped to keep me focused on the job in hand took my mind off the problem for a short while but it was a lifeline for sure. We chat to friends for that is what they become around the world read their posts help where we can post information where we can.  I like @Neverenoughwatches some times think of members past and wonder if they are still at the watches or given up, some drop in for advise and drop out again never to be heard of again. The forum reminds me of Yorkshire hospitality, The door is always open and the kettle on the stove. Long may it continue.   My two bobs worth.
    • KenD
      Main spring

      By KenD · Posted

      Thanks all.   Movement is a Helvetia 800C. Don't know any history e.g. if the broken mainspring is original. Watch was bought recently as non-working. Really interesting piece that Jon, thanks. I'd only been thinking of length relating to power reserve. I don't have a mainspring winder (yet) so I'd like to avoid winding the spring into the barrel by hand. The old spring measures at 1.60 x .11 x ~290. Sorry, can't be exact on the length. The piece I still have is 275, but the second piece escaped during measurement. Best measurement I had for it was ~13. The micrometer does zero accurately so I'm pretty confident of the .11 Also, I'm getting the barrel ID at 9.5 on a vernier. I'm now wondering about going with a .11 spring? Given all of the above, maybe 1.60 x .11 x 300 x 9? Any thoughts? Cheers.
    • VWatchie
      Without Our Forum

      By VWatchie · Posted

      Funny that you should bring this up. I was thinking about it just the other day. What happens if something happens to @Mark? The social bit is fantastic and I would miss it dearly, but I worry even more about the content. Together we have created a gold mine of information which would be more or less irreplaceable if the site should disappear. People (often with a lot of knowledge) come and go. I sometimes wonder what happened to them and miss them. We have no idea unless we have some private contact information. When I was new here I saw a lot of posts by @Lawson. He had a true fire in his heart for horology and was asking for an apprenticeship in his signature. I found that very inspiring and often wondered what happened. Is the fire still burning? Did he get an apprenticeship?
    • clockboy
      Intro

      By clockboy · Posted

      Welcome to the forum, enjoy.
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont like to give up things that i enjoy Tom.  So my next question is how are we going to prepare for that inevitability and what are we going to do about it. Its not just about funding it but I did pick up on something that Mark said once. It doesnt run on fresh air , what if it becomes a burden or an unnecessary cost or for any other reason that i wont get into. We all know life can change in an instant, my life has been so up and down for about 8 years and was only just beginning to level itself out. 
×
×
  • Create New...